manualshive.com logo in svg

SeeMeCNC ERIS DELTA, Manual

Share
Download
SeeMeCNC ERIS DELTA Manual Download Page 23

This can be handy when you're printing a small part and you're having bed adhesion 

issues and you don't want to have to use a raft.  Later on in the 

Advanced

 settings section, 

you'll see more options on how you can tweak the 

Skirt and Brim

 settings.

Support Material

 – With the 

Standard

 and 

Advanced

 setting levels, you get more 

control over how the support material for your part is generated.

The new option here is called 

Support Type

 and allows you to choose a 

LINES

 or 

GRID

pattern for the support material.  When I printed the support example, I used the 

LINES

 mode 

as that is the default for the 

Simple

 settings mode.  Looking down on it from above, this is what 

the 

LINES

 support material pattern looked like for that print.

This shows the second layer of the print.  The lines will continue to stack 

upon one another for the entirety of the support structure.  

The 

GRID

 pattern (on the right) uses the same

spacing as the 

LINES

 option, but is designed to provide

more support where it may help to provide a better end result.

Interface Layers

 will allow you to specify where to place a solid support layer when the 

standard support structure isn't enough for the part you're printing.

Normally MatterSlice will only generate support for those elements that can be supported

with the support structure starting from the bed surface.  If you check 

Support Everywhere

, 

MatterSlice will add support where ever it's needed.

Standard

 also exposes a new support tuning category called 

Support Options

.  Here 

you can adjust the 

Pattern Spacing 

and 

Support Percent

.  

Pattern Spacing

 controls the 

distance between support material lines.  A wider spacing may create support that's easier to 
remove, but may not support as well as a narrower spacing.

Support Percent

 controls when support will be generated.  Most slicing software will 

allow you to define an overhang angle that must be reached before support will be generated.  
MatterSlice looks at it a bit differently.  

Support Percent

 basically instructs MatterSlice that; “If 

the next layer path covers n% or less, you should generate support underneath it.”

Here's a visual example that will help you understand what's

going on.

The layer stack on the right is angled at 45 degrees.  You'll notice

that each layer only overlays the layer below it by around 25%.  With a 

Support Percent

 value set to 50%, this would cause support to be

generated.

Extruders/Support Material Extruder

 tells the slicer which

extruder to use when generating support.  This option is only really
meaningful if you're using two extruders and have one dedicated to a
special filament meant for support structures (such as PVA).

23

Summary of Contents for ERIS DELTA








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands