manualshive.com logo in svg

SEELEY INTERNATIONAL Breezair TBQI, Installation Manual, Page: 2 / 24

Share
Download
SEELEY INTERNATIONAL Breezair TBQI Installation Manual Download Page 2

i 

 |   

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS 

Read And Save These Instructions For Future Reference. 

1

Warnings 1

To Reduce The Risk Of Fire, Electric Shock, Or Injury To Persons, Observe The Following: 

1

Employer And Employee Responsibilities  

1

Installer And Maintenance Contractors - Risk Assessment  

1

Some Points To Consider  

1

Other Important Requirements  

1

QUICK GUIDE 

2

INSTALLATION INSTRUCTIONS 

Cooler Location 

4

Access For Servicing And Maintenance 

4

Removing The Venturi 

4

Removing The Transition 

5

Preparing The Roof Jack 

5

Mounting The Roof Jack 

5

Securing The Roof Jack And Transition  

5

Optional Weatherseal 

6

Existing / Replacement Installations 

6

Fitting The Optional Leg Support Kit 

7

Conveying The Cooler To The Roof 

8

Mounting The Cooler 

8

Cable Installation 

9

Installing The Venturi / Fan Assembly  

9

WATER REQUIREMENTS 

Installing The Float Valve 

10

Installing The Inlet Solenoid 

10

Installing The Water Sensor 

11

Mains Water Connection 

11

Installing The Drain Valve 

11

ELECTRICAL REQUIREMENTS 

Electrical Connection 

12

Multiple Cooler Installations  

13

Connecting The Water Pump 

13

Connecting The MagIQtouch Controller 

14

MAGIQTOUCH CONTROLLER DISPLAY INFORMATION 

14

COMMISSIONING THE COOLER 

Setting The Water Level 

15

Test Operation 

15

Refitting The Pad Frames 

15

Adjusting Cooler Settings 

16

Testing The Pump 

16

Testing The Drain Valve 

16

COMMISSIONING COMPLETION CHECKLIST 

17

FAULT CODES INDICATED BY LED’s ON THE COOLER ELECTRONICS MODULE 

18

TROUBLE SHOOTING 

19

WARNING! Failure to install and commission the product in compliance with these instructions, or failure to do 

the job properly and competently, may void the customer’s warranty. Further, it could expose the Installer and/or 

the Retailer to serious liability.

Summary of Contents for Breezair TBQI

























Reviews:

No comments