SEELEY INTERNATIONAL Braemar Ecostar TQ3, Installation Manual

Page: 11 / 20

10 SEELEY INTERNATIONAL – INSTALLATION MANUAL
Terminate
condensate drain in
a suitable location
Fix flue in place
with screw
Remove &
discard lower
transit plug
Check that
upper transit
plug is secure
Plastic vent cowl and
condensate drain elbow are
supplied in external installation
accessories kit.
Plastic vent cowl.
TQ5 ONLY
Condensate drain elbow
Seal flue and
condensate drain
connections with
silicone sealant or
PVC primer and
solvent cement.
Flue connection - Non modulating heaters Flue connection - Modulating heaters

Attach powder coated die cast flue terminal to heater over flue
outlet, fixing in place using screws supplied.

Powder coated die cast flue terminal and starter collars are
included in external installation accessories kit.

Larger starter collars (400mm) required for the X-Air units are
supplied inside the heater fan inlet.

A flue guard kit is available for external installations. P/No 079073.
External flue terminal
POWDER-COATED DIE CAST VERSION
Heater flue outlet
Condensate drain elbow
Seal flue and
condensate drain
connections with
silicone sealant or
PVC primer and
solvent cement.

Push flue terminal onto heater flue outlet spigot.

Align hole in flue terminal spigot with hole in heater flue outlet, and
secure in place with screws provided in installation kit.

Powder coated steel flue terminal and starter collars are included
in external installation accessories kit.

Larger starter collars (400mm) required for the X30/X32
units are supplied inside the heater fan inlet.

A flue guard kit is available for external installations.P/No 079073.
Terminate condensate
drain in a suitable location
Fix flue in place
with screw
Remove &
discard lower
transit plug
Check that
upper transit
plug is secure
External flue terminal
External flue terminal
(stainless steel)
Fix in place
with screw
Heater flue outlet
spigot
A flue terminal and condensate
drain elbow are supplied in
TQM/TQS6 external installation
accessories kit.
P/No 075570
Heaters
Heaters
Heaters
Heaters
TQ516
TQ523
TQ5X23
TQ532
TQ5X32
TQM618
TQM623
TQM6X23
TQM632
TQM6X32
TQS523
TQS5X23
TQS623
TQS6X23
TQM516
TQM520
TQM5X20
TQM530
TQM5X30
TQS420
TQS4X20
A B C D
Dimension (mm)
Heater Model
TQ3 and TQ4 models
TQ5 models
TQ315, TQ415 400 800 760 460
TQ320, TQ420 400 800 760 460
TQ325, TQ425 400 800 760 460
TQ330, TQ430 550 900 870 460
TQ435 550 900 870 460
TQ3X20, TQ4X20 400 800 760 460
TQ3X25, TQ4X25 400 800 760 460
TQ3X30, TQ4X30 550 900 870 460
TQ516 400 1200 460 1160
TQ523 400 1200 460 1160
TQ532 550 1200 460 1160
TQ5X23 400 1200 460 1160
TQ5X32 550 1200 460 1160
Concrete slab Wall opening
TQM5 models
TQM6 models
TQM516 400 800 760 460
TQM520 400 800 760 460
TQM530 550 900 870 460
TQM5X20 400 800 760 460
TQM5X30 550 900 870 460
TQM618 400 1200 460 1160
TQM623 400 1200 460 1160
TQM632 550 1200 460 1160
TQM6X23 400 1200 460 1160
TQM6X32 550 1200 460 1160
TQS models
TQS320, TQS420 400 800 460 760
400 1200 460 1160 TQS523, TQS623
400 800 460 760 TQS3X20, TQS4X20
400 1200 460 1160 TQS5X23, TQS6X23
EXTERNAL INSTALLATION
Heater base

Construct the heater base and prepare wall opening to the
dimensions shown in the table below.

ENSURE THAT THE BASE IS LEVEL IN BOTH DIRECTIONS.

Heater is approved for installation against a wall.

Refer to above kits tabel for flashing kit part numbers.
Concrete slab
Lintel
B
A
D
C
TQ315
TQ320
TQ3X20
TQ325
TQ3X25
TQ330
TQ3X30
TQ415
TQ420
TQ4X20
TQ425
TQ4X25
TQ430
TQ4X30
TQ435
TQS320
TQS3X20