background image

Owner’s Manual

12” B/W Quad Observation System

Model SLM424 System / Model SLM422 Monitor

Customer Support 1-800-774-0284     www.security-labs.com

Security Labs Limited Warranty

Security Labs, Inc. warrants that if a Security Labs product proves to be defective in material 
or workmanship under normal usage, Security Labs will provide, without charge to the 
consumer, parts and/or labor necessary to remedy the defect for the period of 

ONE YEAR

 

from the date of purchase. The warranty period commences on the date that the product is 
purchased by the consumer. Any implied warranty is also limited to the duration above.

THIS WARRANTY DOES NOT COVER THE FOLLOWING: FLUCTUATIONS IN THE 
POWER SOURCE OR LIGHTNING-RELATED DAMAGE; ATTACHED OR UNATTACHED 
ACCESSORIES; COSMETIC PARTS SUCH AS KNOBS AND ACCESS DOORS; CABINET 
DAMAGE, INCLUDING DAMAGE IN TRANSIT; ACCIDENTAL DAMAGE; MISUSE; ABUSE; 
UNAUTHORIZED PARTS USAGE OR REPAIRS; RECEPTION PROBLEMS DUE TO 
INADEQUATE SIGNAL; UNAUTHORIZED INTERNAL CONTROL OF ADJUSTMENTS; 
INSTALLATION; ADJUSTMENT OF CONSUMER CONTROLS, OR ANY OTHER USE OF 
THE PRODUCT OTHER THAN THAT SPECIFICALLY PRESCRIBED IN THE OWNER'S 
MANUAL. THIS WARRANTY APPLIES TO PRODUCTS SOLD AS NEW AND NOT 
REMANUFACTURED OR B-STOCK PRODUCTS.

SECURITY LABS, INC. DOES NOT ASSUME LIABILITY FOR ANY VIOLATION OF PRIVACY 
FROM ILLEGAL AUDIO OR VIDEO MONITORING OR RECORDINGS MADE FROM THIS 
DEVICE. THE USER/OWNER ASSUMES FULL LIABILITY FOR ANY AND ALL 
RECORDINGS MADE FROM THIS DEVICE IN A SECURITY OR SURVEILLANCE 
OPERATION OR IN ANY OTHER USE. SECURITY LABS IS NOT RESPONSIBLE FOR 
RECORDINGS THAT VIOLATE LAWS OR THAT MAY PROVE OFFENSIVE OR TEND TO 
INCRIMINATE ANOTHER INDIVIDUAL. LOCAL, STATE, AND FEDERAL LAWS MUST BE 
OBSERVED REGARDING ALL RECORDINGS AND SURVEILLANCE MONITORING. 
CHECK WITH YOUR GOVERNMENTAL AGENCY FOR COMPLIANCE REQUIREMENTS.

To obtain warranty service, the consumer must provide the product along with evidence that 
will positively identify the date that the product was purchased from an authorized Security 
Labs product representative, dealer, retailer, or distributor. Prior to shipment, a RETURN 
AUTHORIZATION must be obtained from SECURITY LABS; this will assist us in more 
efficient service on your unit, and possibly avoid shipment if the adjustment can be made over 
the phone. If shipment is made, the cost for postage, insurance and shipping of the product is 
the responsibility of the owner.

SECURITY LABS' OBLIGATION UNDER THIS WARRANTY SHALL BE TO REPLACE SUCH 
PARTS AND PROVIDE LABOR AS STATED. SECURITY LABS WILL NOT BE LIABLE FOR 
ANY LOSSES OR INCONVENIENCES, DIRECT OR INDIRECT, OR CONSEQUENTIAL 
PROPERTY DAMAGES. 

To obtain a return authorization number, contact customer service at:

SECURITY LABS, INC.
15540 HERRIMAN BLVD. NOBLESVILLE, IN  46060  USA
CUSTOMER SERVICE: 1-800-774-0284
ONLINE: www.security-labs.com

Summary of Contents for SLM424









Reviews: