Securam ProLogic L01-C Operating Instructions Manual Download Page 9 | Manualshive

Page: 9 / 20

Securam ProLogic L01-C Operating Instructions Manual Download Page 9

ProLogic L01-C

Operation Instructions

9

Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or
the Manager Code (ID01).
The “Select Menu” message will be displayed as follows:

Step 4: Scroll UP to the menu selection “Delete One User” and Press OK

Step 5: Press OK

Step 6: The system will ask to confirm the deletion. Press OK.

This User Code is now deleted from the system.

3.4 Delete All Users
This feature is used to delete all users from the system. Upon executing this command, ID02 will be
deleted and Manager Code will be reset as follows:



Manager Code (ID01) is 123456

Note: Super Code will not be changed.

Step1: Press the Menu/OK button

Step 2: Using the



and



, scroll to the System Menu and Press Menu/OK.

Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or
the Manager Code (ID01). The “Select Menu” message will be displayed as follows:

Step 4: Scroll UP to the menu selection “Delete All Users” and Press OK.

Step 5: The system will request a Confirmation. Press OK.

«
...
7
8
9
10
11
...
»

Summary of Contents for ProLogic L01-C





















Reviews:

No comments