background image

ENFORCER Heavy-Duty Outdoor Stand-Alone Keypad

 

 

SECO-LARM U.S.A., Inc                                                                                      5

 

SECO-LARM U.S.A., Inc.                                                                                                   

               33                                              

5                                                                                         

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Installation: 

1.

 

Unlock the keylock mounted on the face of the keypad 
with one of the included keys. 

2.

 

Open the faceplate of the keypad. The hinge will allow 
the faceplate to open to a 90

°

 angle. 

3.

 

Remove the 1” wiring hole cover from back of keypad.  

4.

 

Run wires into the keypad using the 1” wiring hole on 
the back of the enclosure. 

5.

 

Using the wiring diagram on pg. 4, wire the keypad 
according to the specific application. 

6.

 

Place the included gasket between the keypad and 
mounting surface. 

7.

 

If attaching the keypad to a mounting plate such as a 
gooseneck stand, use the 4 mounting plate holes 
located on the back of the keypad. 

These holes are 
used to mount the 
keypad to a 
gooseneck stand. 

Wiring – Connecting to a Lock Device and Alarm Arm/Disarm: 

1

 Connect a IN4004 diode (not included) as close as possible and in parallel with an electric strike. 

This absorbs possible electromagnetic interference to prevent operation of the strike from 
damaging the keypad. Do not connect a diode when using electromagnetic locks.

 

Please consult the alarm control panel’s manual for more information. 

Cathode 

To alarm control panel  
(24-hour N.C. zone)

2

 

To alarm control panel  
(Alarm arm/disarm control)

2

 

IN4004 

Diode 

Electric strike 

Egress 
button 

EARTH  

GROUND 

12~24 

VAC/VDC 

REED 

OU
TPU

T 1

 

OU
TPU

T 2

 

COM (-) 

EG IN 

N.O. 

COM 

N.C. 

N.O. 

COM 

N.C. 

N.C. 

Tamper 

12~24 

VAC/VDC 

Power Supply 

Magnetic 
contact 

Summary of Contents for ENFORCER SK-3523-SDQ













Reviews: