programming is complete. To enable the Aries (ramming) effect
at the power configured using the VR1 Trimmer, repeat the
above procedure, pressing the SEL key twice (the CODE PED
Led flashes quickly) instead of once. Repeat the operation to
restore the previous configuration.
In this way the lock can be unlocked and the opening phase
can be executed correctly. Before starting the opening process,
the control unit sends a closing command for 2 seconds, at a
power associated with the selection.
E) T. MOT. (Closure strike):
The control unit is supplied by the manufacturer with the
closure strike function not enabled. To enable the function,
proceed as follows: check the extended menu is enabled (the
T. PAUSA and RIT. ANTE LEDs flash in alternation), press the
SEL key until the T. MOT. LED flashes, then press the SET
key: the T. MOT. LED turns on and programming is complete. If
you wish to enable the Closure strike function at the configured
power with the VR1 trimmer, repeat the above procedure,
pressing the SEL key twice (the T.MOT. Led flashes quickly)
instead of once. Repeat the operation to restore the previous
configuration.
If Deceleration during closing is programmed, the control unit
will add 1-sec time at the power associated with the selection
(after completing the decelerated closing phase) in order to
overcome the lock, if present.
F) T. MOT. PED. ( Follow Me ) :
The control unit is supplied by the manufacturer with the Follow
Me function not enabled. To enable the function, proceed as
follows: check the extended menu 1 is enabled (the T.PAUSA
and RIT ANTE LEDs flash in alternation), press the SEL button
until the T.MOT.PED Led flashes, then press the SET key; at
the same time the T.MOT.PED LED turns on and remains
steady and programming is complete. In this way the control
unit executes the closing phase immediately, ignoring the
configured operating logics, if it detects transit with activation of
the photocell connected to the DS input during the opening,
Pause and Closing phases.
Repeat the operation to restore the previous configuration.
EXTENDED MENU 2
The control unit is supplied by the manufacturer with only the
option of directly selecting the functions listed in the main
menu.
To enable the functions listed in Extended Menu 2, proceed as
follows: open Extended Menu 1 (as instructed in the respective
section), then press and hold the SET key for 5 seconds; the
T.PAUSA and RIT ANTE LEDs flash at the same time; you
have 30 seconds to select the functions of Extended Menu 2
using the SEL and SET buttons; after another 30 seconds, the
control unit returns to the main menu.
---------------------- EXTENDED MENU 2 -----------------
Led reference Led off Led on
A) TIPO MOTORE Remote PGM = OFF Remote PGM = ON
B) AUTO PGM Photocell test= OFF Photocell test = ON
C) CODE Pre-flash and Cour. light=OFF Pre-flash or Cour. light=ON
D) CODE PED. Flash in Pause = OFF Flash in Pause = ON
E) T. MOT.
PUL=PUL/PED=PED PUL=PUL/PED=DS AUX1/2
F) T.MOT.PED. PUL=PUL / PED=PED PUL=AP / PED=CH
G) T. PAUSA Flash ON/OFF simultaneously
H) RIT. ANTE Flash ON/OFF simultaneously
A) TYPE OF MOTOR
(Remote programming of radio control):
The control unit enables remote programming of the
transmission code, without using the SEL key.
To program the transmission code in remote mode, proceed as
follows: send the previously stored radio control code
continuously for more than 10 seconds and the control unit will
enter the programming mode as described above for the CODE
Led in the main menu.
The control unit is supplied by the manufacturer with remote
programming of the transmission code not enabled; to enable
the function proceed as follows: check the extended menu 2 is
enabled (the T. PAUSA and RIT. ANTE LEDs flash
simultaneously), press the SEL button until the TIPO MOTOR
LED flashes, then press the SET key, at the same time the LED
TIPO MOTOR turns on and remains steady and programming
is complete. Repeat the operation to restore the previous
configuration.
B) AUTO PGM (Photocell Test):
The control unit is supplied by the manufacturer with
programming of the Photocell Test disabled; to enable the
function (in accordance with standard EN 12453), proceed as
follows: check the extended menu 2 is enabled (the T. PAUSA
and RIT. ANTE LEDs flash simultaneously), press the SEL
button until the AUTO PGM Led flashes, then press the SET
key, at the same time the LED AUTO PGM turns on and
remains steady and programming is complete. In this way, the
Photocell connected to the DS input is tested before the
automation starts any of the phases.
Repeat the operation to restore the previous configuration. If
not used, the DS input must be jumped and the Photocell Test
disabled.
C) CODE (Pre-flash/ Courtesy Light):
The control unit is supplied by the manufacturer with the Pre-
flash and Courtesy Light functions not enabled. To enable the
Pre-flash function, proceed as follows: check the Extended
Menu 2 is enabled (the T. PAUSA and RIT. ANTE LEDs flash
simultaneously), press the SEL key until the CODE LED
flashes, then press the SET key, at the same time the CODE
LED turns on and remains steady and programming is
complete. To enable the Courtesy light function, repeat the
above procedure, pressing the SEL key twice (the CODE LED
flashes quickly) instead of once. Repeat the operation to
restore the previous configuration.
Pre-flashing:
The 12 Vdc 4 W light output is always activated
3 seconds before the automation starts any of the phases.
Courtesy light:
The 12 Vdc 4W light output is activated for 3
seconds whenever an opening command is transmitted.
D) CODE PED (Use of the Flashing Beacon) :
The control unit is supplied by the manufacturer with use of the
flashing beacon during the Pause Time disabled. To enable
use of the flashing beacon, check the Extended Menu 2 is
enabled (the T. PAUSA and RIT. ANTE LEDs flash
simultaneously), press the SEL key until the CODE PED LED
flashes, then press the SET key, at the same time the CODE
PED LED turns on and remains steady and programming is
complete. Repeat the operation to restore the previous
configuration.
E) T. MOT. (Selection of the PED / DS AUX1-AUX2 input) :
The control unit is supplied by the manufacturer with a PED
input for connecting a cyclical (NO) Pedestrian control button.
To select use of the input as DS AUX 1, proceed as follows:
check the Extended Menu 2 is enabled (
the T.
PAUSA and RIT. ANTE LEDs flash simultaneously), press the
SEL key until the
T.MOT. LED flashes, then press the SET key,
at the same time the T.MOT. LED turns on and remains steady
and programming is complete
.
Repeat the operation to restore the previous configuration.
To select use of the input as DS AUX 2, repeat the above
procedure for use as DS AUX 1, pressing the SEL key twice
(the T. PAUSA and RIT. ANTE LEDs flash quickly and at the
same time) instead of once.
Repeat the operation to restore the previous configuration.
F) T. MOT. PED. (Selection of the PUL and PED inputs) :
The control unit is supplied by the manufacturer with a PUL
control input for connecting a cyclical (NO) main control button,
and a PED control input for connecting a cyclical (NO)
Pedestrian control button. To select a different use for the PUL
and PED inputs, proceed as follows: check the Extended Menu
2 is enabled (the T. PAUSA and RIT. ANTE LEDs flash
4 Rev. 1.0 08/10/2010
Summary of Contents for LRS 2239
Page 7: ...7 Rev 1 0 08 10 2010 ...
