background image

9

Side Mount & Splashwell Mount Cylinders

FILLING & PURGING 

THE SYSTEM

Filling the helm full of oil can be 

done faster if oil is poured into 

the helm prior to connecting filler 

tube and oil bottle to the helm.

NOTICE

FILLER PLUG

(REMOVED)

FILLER KIT

HELM FILL

PORT

DO NOT LET 

OIL LEVEL 

FALL BELOW

THIS POINT

PUSH PIN

Figure 7. 

SeaStar Solutions recommends the use of 

SeaStar Steering Fluid ONLY

SeaStar Steering Systems have been engineered and validated 

using our proprietary SeaStar Hydraulic Fluid.

Any non-approved fluid may cause serious damage to the steering 

system resulting in possible loss of steering, causing property 

damage, personal injury and/or death.

In an emergency, SeaStar EPS Fluid, any MD-3/4 rated ATF or MIL-PRF-

5606H equivalent fluid that is filtered through a fine mesh screen can 

be used. The system MUST be thoroughly flushed as soon as possible 

with genuine SeaStar Steering Fluid after using an emergency fluid. 

In 

an EXTREME emergency, any non-toxic, non-flammable fluid that is 

filtered through a fine mesh screen may provide temporary steering.

Hydraulic Fluid 

Emergency Use Fluids 

Steps 1 – 5 noted on page 10 refer to a single station, single 

cylinder installation. For twin station and/or twin cylinder installations 

you MUST perform steps 1 – 5 first, then, see page 11 to complete 

the removal of air from the system.

This procedure requires two people. One person may not be able to 

remove all the air from the system which will result in spongy, 

unresponsive steering.

During the entire filling procedure, oil 

must

 be visible in the filler tube. 

Do NOT

 allow the oil level to disappear into the helm pump, as this 

may introduce air into the system and increase your filling time.

Read First

NOTICE

Power Purge Users.

 Please refer to the instructions included with 

your power purge unit.

Power Assist Users. 

You MUST refer to the bleeding instructions 

included with your SeaStar Power Assist Unit.

NOTICE

NOTICE

 

WARNING

 

WARNING

Never fill or mix brake fluids, 

trigycerides or polyalkylene 

glycols within a hydraulic 

steering system.

Summary of Contents for BayStar





















Reviews: