SeaSoft MobilGate - 128c Manual Download Page 10

Page: 10 / 11

d) After downloading a configuration from PC via USB, the device will restart which takes 30-40

seconds, and it will be operational after registering to a GSM network.

e) All members of the

MobilGate

family can operate only with SIM cards that are not protected with

PIN codes. Please note that the SIM PIN is not equal to the module PIN number.

Before device use, the PIN code has to be removed from the SIM card.

g) By using pre-paid SIM card, showing the caller ID must be enabled. This can be performed by

contacting the carrier’s customer service.

h) Call-forwarding and SMS reminders about missed calls sent by the carrier must be disabled on the

SIM card.

9. Connecting the MobilGate-128c

10. Specifications

Power supply:

10–30 Vdc

GSM:

Dual band

Max. Current:

290 mA

Frequency:

900/1800MHz

Stdby current (relays on):

27 mA

Communication:

SMS, voice

Stdby current (relays off):

135 mA

Aerial conn.:

SMA

Operating temperature

-30 - +70 C

Enclosure:

DIN rail enclosure

Dimensions:

107 x 90 x 66 mm

SeaSoft

Ltd

. -

2013

SeaSoft Ltd.

www.seasoft.hu - www.mobil-control.eu T: (+36) 62 406405 M: (+36) 30 2557688 F: (+36) 62 405-969

Summary of Contents for MobilGate - 128c












Search results

Summary of Contents for MobilGate - 128c

Reviews:

Related manuals for MobilGate - 128c

Brands by name

Popular brands

SeaSoft MobilGate - 128c, Manual

Search results

Summary of Contents for MobilGate - 128c

Reviews:

Related manuals for MobilGate - 128c

Brands by name

Popular brands