background image

2

CONTENTS

INTRODUCTION/WARRANTY ..........................................2
SAFETY ...............................................................................2
PREPARATION....................................................................3
INSTALLATION ................................................................3-4
ELECTRICAL.....................................................................5-6
OPERATION........................................................................7
MAINTENANCE ...............................................................8-9
TROUBLESHOOTING .......................................................10
REPAIR PARTS ..................................................................11

INTRODUCTION

Please take a few minutes to read our instructions before you
install and use your pump. This will help you obtain the full
benefits from this pump. It will also help you avoid any need-
less service costs that result from causes we cannot control
and cannot cover in our warranty.

Carefully read and follow all safety instructions in this
manual or on pump.

This is the safety alert symbol.

When you see this

symbol on your pump or in this manual, look for one of the
following signal words and be alert to the potential for per-
sonal injury!

DANGER 

warns about hazards that will cause

serious personal injury, death or major property damage if
ignored.

WARNING 

warns about hazards that can

cause serious personal injury, death or major property dam-
age if ignored.

CAUTION 

warns about hazards that will or can

cause minor personal injury or property damage if ignored.

The word 

NOTICE 

indicates special instructions which are

important but not related to hazards.

1. To avoid risk of serious bodily injury and property dam-

age, read safety instructions carefully before installing
pump.

2. Follow local and/or national plumbing and electrical

codes when installing pump.

3. Keep the well covered while installing pump to prevent

leaves and other debris from falling into well, contami-
nating well and possibly damaging pump.

4. Protect pump and piping system from freezing. Allowing

pump or water system to freeze could severely damage
pump and voids warranty.

Hazardous Voltage. Can shock, burn,

cause death, or start fires.

5. Disconnect electrical power source before installing or

working on pump.

6. Ground pump with a ground wire run from grounding lug

on motor to a grounded lead in the service panel.

7. Line voltage and frequency of electrical power supply

must agree with motor nameplate.

8. Use of fuses or wire smaller than size recommended in

owner’s manual can cause overheating, possible fires, and
will void warranty.

9. Pump water only with this pump.

10. Do not run pump dry. To do so will damage seals and can

cause leaking and property damage.

FULL ONE YEAR WARRANTY ON CRAFTSMAN

®

SPRINKLER PUMPS

For one year from the date of purchase, Sears will repair or replace this pump, free of charge, if defective in materi-
als or workmanship.

LIMITED WARRANTY ON CRAFTSMAN

®

HYDROGLASS

®

SPRINKLER PUMP

After one year and through two years from the date of purchase, Sears will furnish, free of charge, a replacement
part for any defective part. You pay for labor.

This warranty does not cover repairs on replacement parts necessary because of abuse or negligence including fail-
ure to install, adjust and operate this pump according to the instructions in the owner’s manual.

LIMITATION OF LIABILITY

SEARS WILL NOT BE LIABLE FOR LOSS OR DAMAGE TO PROPERTY OR ANY INCIDENTAL OR CONSEQUENTIAL
LOSS OR EXPENSE FROM PROPERTY DAMAGE DUE DIRECTLY OR INDIRECTLY FROM THE USE OF THIS
PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPART-
MENT IN THE UNITED STATES. 

This warranty applies only while the product is in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179

RULES FOR SAFE INSTALLATION AND OPERATION!

Summary of Contents for CRAFTSMAN HYDROGLASS 390.2622













Reviews: