Sears Craftsman 944.600940 Owner'S Manual Download | Manualshive

Page: 8 / 60

background image

8

FIG. 4

ASSEMBLE GAUGE WHEELS AND
BRACKETS TO MOWER DECK (See Fig. 4)

The gauge wheels are designed to keep the mower deck in
proper position when operating mower. Be sure they are
properly adjusted to ensure optimum mower performance.
•

Attach front gauge wheel brackets marked front left
(FL), front right (FR) to mower deck using (3) carriage
bolts and (3) locknuts. For ease of installation do not
tighten locknuts until all carriage bolts have been in-
stalled.

•

Attach rear gauge wheel brackets marked rear left (R L),
rear right (RR) to mower deck using (3) carriage bolts and
(3) locknuts. For ease of installation do not tighten
locknuts until all carriage bolts have been installed.

•

Slide gauge wheel bar down into bracket channel, Be
sure that gauge wheel bar aligning holes are on top.
Assemble gauge wheels as shown using shoulder bolts,
3/8 washers and 3/8-16 center locknuts and tighten
securely.

•

Adjust gauge wheels to highest position for ease of
mower deck assembly.

•

Adjust gauge wheels before operating mower as shown
in the operation section of this manual.

SHOULDER
BOLT

GAUGE
WHEEL

3/8-16 CENTER
LOCKNUT

GAUGE
WHEEL
MOUNTING
BRACKET

3/8 WASHER

CARRIAGE
BOLTS

CROWNLOCK
NUT

ADJUSTING
BAR

PIN

RETAINER
SPRING

ASSEMBLY

«
...
6
7
8
9
10
...
»

Summary of Contents for Craftsman 944.600940





























































Reviews:

No comments

Related manuals for Craftsman 944.600940

Brand: Washtech Pages: 30

E15TC75HSS - ICON Designer

Brand: Electrolux Pages: 2

E15TC75HPS - Fully Integrated Trash Compactor

Brand: Electrolux Pages: 44

EI15TC65HS - Undercounter Trash Compactor

Brand: Electrolux Pages: 12

EI15TC65HS - Undercounter Trash Compactor

Brand: Electrolux Pages: 2

Brand: TILMOR Pages: 2

Brand: Ariens Pages: 30

Brand: MTD Pages: 80

Brand: Wheel Horse Pages: 12

Brand: townew Pages: 8

Tractor TURBOMIX MTXH

Brand: Bauer Pages: 42

Brand: Vari Pages: 9

Brand: Summit Pages: 35

Brand: GOLDONI Pages: 60

Brand: GOLDONI Pages: 122

Brand: GOLDONI Pages: 168

Brand: GOLDONI Pages: 200

Brand: Challenger Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands