background image

2

CONTENTS

INTRODUCTION/WARRANTY ..................................2
MAJOR COMPONENTS ..............................................3
PUMP PERFORMANCE...............................................4
INSTALLATION........................................................4-8
ELECTRICAL ............................................................8-9
OPERATION ........................................................10-11
HELPFUL HINTS / MAINTENANCE.....................11-14
TROUBLESHOOTING GUIDE ..................................15
REPAIR PARTS .....................................................16-19

INTRODUCTION

Please read our instructions before installing and using
your Deep Well Jet Pump. This will help you obtain the
full benefits of the quality and convenience built into
this equipment. It will also help you avoid any needless
service expense resulting from causes beyond our con-
trol which are not covered by our warranty.

Carefully read and follow all safety instructions in this
manual or on pump

This is the safety alert symbol. When you see this

symbol on your pump or in this manual, look for

one of the following signal words and be alert to the
potential for personal injury!

Warns about hazards that 

will 

cause seri-

ous personal injury, death or major property damage if
ignored.

Warns about hazards that 

will 

or 

can

cause serious personal injury, death or major property
damage if ignored.

Warns about hazards that 

will 

or 

can 

cause

minor personal injury or property damage if ignored.
The word 

NOTICE 

indicates special instructions

which are important but not related to hazards.

1. To avoid risk of serious bodily injury and property

damage, read safety instructions carefully before in-
stalling pump.

2. Follow local and/or national plumbing and electri-

cal codes when installing pump.

3. Keep well covered while installing pump to prevent

leaves and other debris from falling into well, con-
taminating well and possibly damaging pump.

4. Protect pump and piping system from freezing.

Allowing pump or water system to freeze could
severely damage pump and voids warranty.

To  avoid serious injury and equip-

ment damage, limit system pressure to 100
pounds per square inch (PSI) or below at all
times. Over-pressure can cause tank blowup; in-
stall relief valve capable of passing full pump vol-
ume at 100 PSI.

5. With a new well, test well for purity before use.

Consult local Health Department for procedure.

Hazardous voltage. Can shock, burn,

cause death, or start fires.

6. Disconnect electrical power source before in-

stalling or working on pump.

7. Ground pump with a ground wire run from ground-

ing lug on motor to a grounded lead in the service
panel.

8. Line voltage and frequency of electrical power sup-

ply must agree with motor nameplate.

9. Use of fuses or wire smaller than size recommended

in owner’s manual can cause overheating, possible
fires, and will void warranty.

10. This pump is a deep well jet pump. It is not de-

signed or intended for shallow well use. Use in a
deep well (more than 25’ depth to water).

FULL ONE YEAR WARRANTY ON CRAFTSMAN

®

WELL PUMP

For one year from the date of purchase, Sears will repair or replace this pump, free of charge, if defective in material or
workmanship.

This warranty does not cover repairs or replacement parts necessary because of abuse or negligence including failure to
install, adjust and operate this pump according to the instructions in the owner’s manual.

LIMITATION OF  LIABILITY

SEARS WILL NOT BE LIABLE FOR LOSS OR DAMAGE TO PROPERTY OR ANY INCIDENTAL OR CONSEQUENTIAL LOSS
OR EXPENSE FROM PROPERTY DAMAGE DUE DIRECTLY OR INDIRECTLY FROM THE USE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or 
exclusion may not apply to you.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT
IN THE UNITED STATES.
This warranty applies only while the product is in use in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from  state to state.

Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179

RULES FOR SAFE INSTALLATION AND OPERATION

Summary of Contents for CRAFTSMAN 390.2532





















Reviews: