background image

Key

Part

Part

No.

Number

Description

1**

J218-600C

Motor

2

L43-5C

Connector

3

U36-112ZP

Locknut - 1/2”

4

U217-1228

Pressure Switch

5

U37-672P

Switch Tube - 14-1/2”

6

J212-24A

Pressure Regulator Assembly

7

L2-16A

Adapter

8

U30-75ZP

Capscrew - 3/8”-16x1-1/4” Lg. (2 Req.)

9

U65-15SS

Shaft Key (2 Req.)

10

U109-99

Seal - Shaft

11

J24-11

Spring Holder

12

J105-76P

Impeller (2 Req.)

13

J43-23

Spacer - Impeller 

14

J101-26

Intermediate Volute w/Wear Rings

14A

J20-11

Gasket (2 Req.)

14B

J23-10

Wear Ring (2 Req.)

14C

J23-11

Wear Ring

15

U36-175D

Impeller Nut

16

J101-33

Base Volute w/Wear Ring

17

U78-57CT

Pipe Plug - 1/4” NPT

18

*

Capscrew - 3/8”-16x4-1/4” Lg. (4 Req.)

Repair Parts List - Multi-Stage Jet

* Standard hardware item; may be purchased locally.

** Not mailable; specify freight or express.

For repair or service to motors, always give the Motor Model number and any other data found on the motor model plate.

This is a repair parts list, not a packing list. Please order by part number – not by key number.

REPAIR PARTS

16

20

100

80

60

40

9

10

1

3

4

5

6

7

8

2

11

17

16  

15 

14A  

14A  

14B

14B

14C

13 

14

18

1281 0994

12 

12 

Multi-Stage

Jet Pump

Summary of Contents for CRAFTSMAN 390.2532





















Reviews: