background image

Declaration of Conformity 

We, the sole importer into the UK, declare that the product listed below is in conformity with the following EEC 

standards and directives. 

 

The construction file for this product is held by the Manufacturer and 

may be inspected on request by contacting Jack Sealey Ltd

For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery

Hydraulic Floor Press  

Model: YK30F.V2

2006/42/EC Machinery Directive

93/68/EEC CE Marking Directive

Signed by Mark Sweetman

 21st October 2008

NOTE:

  It  is  our  policy  to  continually  improve  products  and  as  such  we  reserve  the  right  to  alter  data,  specifications  and  component  parts  without  prior  notice.

IMPORTANT: 

No liability is accepted for incorrect use of product. 

WARRANTY: 

Guarantee is 12 months from purchase date, proof of which will be required for any claim. 

INFORMATION: 

For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

Sole UK Distributor, 

Sealey Group

,  

Bury St. Edmunds, 

Suffolk.

01284 757500

[email protected]

    

01284 703534

e-mail

Web

www.sealey.co.uk

  6.  DECLARATION OF CONFORMITY

Note:  

Maintenance and repair must only be carried out by qualified person. Contact your Sealey dealer for details.

5.1

  

Periodically lubricate all joints and moving parts.

5.2

  

Always keep the press clean, dry, and protected from harsh conditions.

5.3

  

Before checking the oil level make sure the ram is fully retracted. Remove the oil filler plug 

(39) 

from the top of the pump. The oil level   

 

should be just below the bottom of the filler hole. If it needs filling, use only Sealey hydraulic jack oil. (DO NOT use brake fluid. Contact  

 

your local Sealey dealer for details). Replace oil filler nut and purge system of air (see 4.1.2).

5.4

  

When replacing the hydraulic oil, ensure the piston is fully retracted.

5.5

  

If press efficiency begins to drop, purge the system to eliminate any air from the hydraulic system (see 4.1.2).

5.6

 

When not in use, store the press in a dry, childproof location with the ram and piston fully retracted.  

  5.  MAINTENANCE

IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE PRESS.

Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK. 

DO NOT RETURN PRODUCT TO SEALEY.

 Please telephone Sealey on 01284 757500 to obtain the address and phone number of your local 

agent. 

If product is under guarantee please contact your dealer.

De-commissioning Product

Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the 

product and the oil according to local regulations.

4.1 

INSTALLATION.

4.1.1  Securely attach the press to a flat, firm, level surface taking into account clearance for working pieces. 

 

DANGER! The press is top heavy

. If it requires moving after assembly or for relocation, use suitable slings around the top crossbeam,  

 

or lift direct with a forklift with the forks located under the top crossbeam. 

DO NOT

 use a pallet truck.

4.1.2 

Purge hydraulic system.

 

Before operating the press, the hydraulic system may require purging in order to eliminate any air that may have built up during transit.  

 

Open the release valve (34) by turning anti-clockwise and pump the handle (32) several times. 

 

Should the system malfunction at any time, repeating this procedure may resolve the problem.

 

DANGER! 

Press is purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always    

 

ensure the workpiece is secured on the table to ensure loads that flex will not suddenly “give” causing danger to operator or damage to 

 

component. Ensure you have read and understood chapter 1 safety instructions.  

4.2 

OPERATING INSTRUCTIONS.

4.2.1   Position the work table at the required operating height by inserting the support pins into the appropriate holes in the main frame.

4.2.2   Place the support blocks (12)

 

onto work table (11), then place the workpiece onto the support blocks and align beneath the ram as  

 

 

required. 

Note:

 care must be taken to ensure a support block does not fall from the press work table. If necessary hold the configuration  

 

in position with clamps.

4.2.3   Close the release valve (34) 

by turning it clockwise until it is firmly closed.

4.2.4   Pump handle (32) to quickly bring the ram into position on the workpiece. Before applying any pressure to the workpiece, recheck  

 

 

the alignment with the ram and ensure that the workpiece and press tools are supported in such a way that they cannot flex.

  

WARNING!

 

DO NOT

 apply off centre loads.

4.2.5  Use the pump handle (33) for smaller more controlled movements and applying load onto workpiece.

4.2.6  When work is done, stop pumping the handle. Slowly and carefully free load from workpiece by turning the release valve (34) 

 

anti-clockwise in small increments. 

Note:

 Always keep the piston retracted after use to avoid ram corrosion.

4.2.7   Once ram has fully retracted, remove workpiece from work table.

Note:  

Always keep the piston retracted after use.

  4.  INSTALLATION & OPERATING

YK30F.V2

Issue No: 1 - 20/10/08

Reviews: