Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Contents
OEM Number
Item
Part
Number
Description
Ford
Volvo
Mazda
1
VSE6160-01-V2 Camshaft Alignment Plate >5-11
303-1565
2
VSE6160-02-V2
Camshaft Alignment Plate >5-11
303-1504
999-7405
303-1061
3
VSE6160-03-V2
Crank
Sensor
Alignment
Tool
303-1521
999-7416
4
VSE5042A.10-V2
Crankshaft
Timing
Pin
303-748
999-7406
303-507
5
VSE6160-04-V2
Tensioner Pin (Ø2mm)
303-1054
6
VSE5042-11-V2
Camshaft Sprocket Alignment Plate
303-1097
999-7429
7
VSE5850 -V2
Crankshaft Pulley Alignment Plate
303-1550 999-7431/999-7415
8
VSE6160-05-V2
Crankshaft
Pulley
Alignment
Plate
205-072
9
VSE6160-06-V2
Crankshaft
Pulley
Alignment
Tool
999-7415
Original Language Version
VSE6160.V2 Issue:1 06/07/22
© Jack Sealey Limited
Comprehensive kit covers engines which are fitted to a large range of Ford, Volvo and some Mazda vehicles. Contains time-saving tooling to correctly align
the timing covers on Ford and Volvo engines, and a crankshaft pulley holder for Mazda engines. Supplied in storage case with instructions and warning tag.
TIMING TOOL KIT - FOR FORD, MAZDA, VOLVO 1.5,
1.6, 2.0 - BELT/CHAIN DRIVE
MODEL NO:
VSE6160.V2
1. SAFETY
2. INTRODUCTION
3. CONTENTS
IMPORTANT!
These instructions are provided as a guide only. Always refer to the vehicle manufacturer’s service instructions
or a proprietary manual to establish the correct procedure and data.
WARNING!
Wear approved eye protection. Wear appropriate Personal Protective Equipment. A full range of Personal Protective Equipment
is available from your Sealey stockist.
WARNING!
Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to when using
tools.
WARNING!
Incorrect or out of phase camshaft timing can result in contact between the valve head and the piston crown causing damage to engine.
WARNING!
The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations. The Operator / user
must apply caution and common sense (good practical sense).
8
DO NOT
use tools if damaged.
8
DO NOT
attempt to start or move a vehicle whilst in gear and with timing devices fitted.
9
Wear suitable clothing to avoid snagging.
DO NOT
wear jewellery. Tie back long hair.
9
Ensure that a vehicle that has been raised by a jack is adequately supported. Use axle stands.
9
When timing an engine, always prevent the engine from being turned over. Use a notice and / or inhibit the engine.
9
Keep children and unauthorised persons away from the work area.
9
Maintain tools to ensure that they are in an adequate condition for safe use and optimum performance.
9
Account for all tools, parts and components being used.
DO NOT
leave these in or near the engine.
9
Return tools to suitable storage after use.
9
When not in use, store in a safe, dry childproof place.
Refer to
instruction
manual
Wear eye
protection
