background image

NOTE: 

It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTaNT:

 no liability is accepted for incorrect use of this product.

WaRRaNTy:

 Guarantee is 12 months from purchase date, proof of which will be required for any claim.

Sole UK distributor, Sealey Group.

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk.

IP32 7AR

www.sealey.co.uk

[email protected]

01284 757500

01284 703534

Web

 

environmental Protection

Recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be 

sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)

into approved containers and dispose of the product and the fluids according to local regulations.

VS4825 | Issue 2(SP) 03/07/15

Original Language Version

© Jack Sealey Limited

  pointer passes ‘notch’ “C” - repeat the tensioning procedure.

  

 

fig.11

fig.12

Summary of Contents for VS4825







Reviews: