Oscillating Belt/spindle sander 230V
Model no:
sM1300
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
1.1.
electrical safety
Warning!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
8
dO nOt
pull or carry the appliance by the power cable.
8
dO nOt
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
dO nOt
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
qualified electricia
n.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8
dO nOt
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
general safety
9
Familiarise yourself with the application, limitations and potential hazards of the machine.
Warning!
ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to.
Warning!
disconnect from the electric power supply before changing accessories, servicing or performing any maintenance.
Warning! dO nOt
sand any materials containing asbestos.
9
Maintain the machine and keep in good condition (use an authorised service agent).
9
Check the alignment of moving parts regularly. For safest performance keep the machine clean at all times.
9
Before each use check all abrasive attachments for condition. If worn or damaged replace immediately.
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts are dangerous and will invalidate the warranty.
9
locate the machine in a suitable area. Keep area clean, uncluttered and ensure there is adequate lighting.
9
ensure the machine is situated on a solid work surface, adequate for supporting the weight of the machine and the workpiece.
9
ensure there are no flammable or combustible materials near the work area.
9
Remove ill fitting clothing, ties and loose jewellery, and tie back long hair.
9
Maintain correct balance and footing, ensure the floor is not slippery and wear non-slip shoes.
9
Keep hands and body clear of the worktable when operating the machine.
9
Wear approved safety eye or face protection when operating the machine. If dust is generated respiratory protection must be worn.
8
dO nOt
operate the machine when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
dO nOt
leave the machine running unattended.
8
dO nOt
touch the abrasive whilst operating, or whilst sander is plugged into the electric supply.
8
dO nOt
switch the machine on while the workpiece is in contact with the abrasive.
8
dO nOt
operate the machine if any parts are damaged or missing as this may cause failure or possible personal injury.
8
dO nOt
allow children or untrained persons to operate the machine. Keep them away from the work area.
8
dO nOt
use the machine for any purpose other than wood finishing.
9
When not in use unplug from the mains electrical supply and store in a safe, dry, childproof location.
Recommended fuse rating
3 Amp
S
M1300 Issue 2 (HF) 24/05/18
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear eye
protection
Wear ear
protection
Wear a mask
