background image

5.4.    

check the polarity of the battery posts. the PositiVe (Pos, P, +) battery post usually has a larger diameter than the neGAtiVe  

 

(neG, n, -) post.

5.5.    

determine which post of the battery is earthed (connected) to the chassis. if the negative post is earthed to the chassis (as in most  

 

vehicles), see step 5.6. if the positive post is grounded to the chassis, see step 5.7.

5.6.    

For a negative-grounded vehicle

, connect the PositiVe (red) clamp from the Power Pack to the PositiVe (Pos, P, +) post of  

 

the battery. connect the neGAtiVe (BlAcK) clamp to the vehicle chassis or engine block away from the battery. 

DO NOT

  

 

connect the clamp to the carburettor, fuel lines or sheet-metal body parts. connect to a heavy gauge metal part of the chassis or   

 

engine block.

5.7.    

For a positive-earthed vehicle

, connect the neGAtiVe (BlAcK) clamp from the Power Pack to the neGAtiVe (neG, n, -)  

 

 

post of the battery. connect the PositiVe (red) clamp to the vehicle chassis or engine block away from the battery. 

DO NOT

    

 

connect the clamp to the carburettor, fuel lines or sheet-metal body parts. connect to a heavy gauge metal part of the chassis or   

 

engine block.

5.8.    

When disconnecting the unit, press the jump start button to turn off, remove the clamp from the vehicle chassis, then remove the   

 

clamp from the battery terminal.

6.  FEATURES

1. 

12V 3-pin socket for recharging

2. 

12V dc port

3. 

usB ports

4. 

Battery clamps

5. 

12V/usB/language button

6. 

charging led indicator

7. 

digital display

8. 

Jump start button

9. 

230V/50Hz charger

10. 

12V dc car charger

11. 

12V port adaptor

7.  CONTROL PANEL

7.1.    

DIGITAL DISPLAy

 

When the clamps are connected to a vehicle’s battery, the digital display indicates the battery’s voltage. When not connected to a battery,    

 

the digital display is used to indicate the percent of charge of the jump starter’s internal battery. See 

Display Messages

 for a complete list of  

 messages. 

 

NOTE: 

If the vehicle’s battery voltage is too low to detect, the display will remain blank; the voltage will not display. A manual start procedure  

 

is required to enable the jump start function. see section 9.2, 

Starting a Battery with Low Voltage

.

 NOTE: 

during charging, the display will go into sleep mode and will not display any messages. to turn the display back on, press any  

 button

 

LED INDICATOR

 

Green LED solid –

 the internal battery is charging.

 

Green LED flashing – 

charging has aborted.

 

Green LED pulsing – 

the internal battery is fully charged.

 

9

10

11

sl2s | issue 1  27/07/17

Original Language Version

© Jack sealey limited

FUNCTION BUTTONS

12V/USB/LANGUAGE –

  

enables the 12V dc port and the usB ports.

Press button for 5 seconds to select the language on the display:  

e

N → DE → FR

jUMP START – 

enables the jump start function

Summary of Contents for SL2S







Reviews: