9
Use the compressor in a well ventilated area and ensure it is placed on a firm surface.
9
Keep tools and other items away from the compressor when it is in use, and keep area clean and clear of unnecessary items.
9
Ensure the air hose is not tangled, twisted or pinched.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
disassemble compressor for any reason. The unit must be checked by qualified personnel only.
8
DO NOT
use the compressor outdoors, or in damp, or wet, locations.
8
DO NOT
operate within the vicinity of flammable liquids, gases or solids.
8
DO NOT
touch compressor cylinder, cylinder head or pipe from head to tank as these may be hot.
8
DO NOT
use this product to perform a task for which it has not been designed.
8
DO NOT
deface the certification plate attached to the compressor tank.
8
DO NOT
cover the compressor or restrict air flow around the unit whilst operating.
▲
DANGER! DO NOT
direct the output jet of air towards people or animals.
8
DO NOT
operate the compressor without an air filter.
8
DO NOT
allow anyone to operate the compressor unless they have received full instructions.
WARNING!
The air tank is a pressure vessel and the following safety measures apply:
8
DO NOT
tamper with the safety valve,
DO NOT
modify or alter the tank in any way and
DO NOT
strap anything to the tank.
8
DO NOT
subject the tank to impact, vibration or to heat and
8
DO NOT
allow contact with abrasives or corrosives.
9
Drain condensation from tank daily and inspect inside walls for corrosion every three months and have a detailed tank inspection
carried out annually. The tank shell must not fall below the certified thickness at any point.
WARNING!
For this reason
DO NOT
tamper with, or adjust, the pre-set switch or safety valve.
9
Should there appear to be any loss of efficiency when using the compressor, ensure first that the air tool is clean and functioning
properly. If the air tool is satisfactory then refer to the trouble shooting guide.
1.3.
INSPECTION OF PRESSURE TANK BOTH INTERNAL AND EXTERNAL.
Under the
PRESSURE SYSTEMS SAFETY REGULATIONS 2000
it is the responsibility of the owner of the compressor to initiate a
system of inspection that both defines the frequency of the inspection and appoints a person who has specific responsibility for
carrying out the inspection.
8
DO NOT
carry out any welding operations on any pressurised parts of the vessel.
WARNING!
If an electrical fuse blows, ensure it is replaced with an identical fuse type and rating.
9
When not in use, store the compressor carefully in a safe, dry, childproof location.
2. INTRODUCTION
Low noise compressor runs at only 79dB(A), suitable for places where a standard compressor would disturb work or people in the
vicinity. Aluminium cylinder head with cast iron cylinder gives added resistance to wear. Ideal for use where an oil free air delivery is
required. Suitable for general purpose workshop applications.
3. SPECIFICATION
4. PREPARATION AND ASSEMBLY
4.1.
Remove compressor from packaging and inspect for any shortages or damage. If anything is found to be missing or damaged contact
your supplier.
4.2.
Confirm that the mains voltage corresponds with the voltage shown on the compressor data plate.
4.3.
The compressor should be installed on a flat surface, or one that does not exceed 10° either transversely or longitudinally, and should
be in a position that allows good air circulation around the unit.
Model No:
SAC0607S
SAC2410S
SAC5016S
A
ir Displacement cfm(L/min)
3.1(89)
5.3(150)
6.9(196)
M
aximum Free Air Delivery cfm(L/min):
1.6(44)
2.6(73)
3.4(97)
Maximum Pressure: psi(bar)
116(8)
116(8)
116(8)
Minimum Rated Supply:
230V
230V
230V
Motor Output: hp
0.7
1
1.6
Outlet:
Quick Release Coupling Quick Release Coupling
Quick Release Coupling
Phase:
1ph
1ph
1ph
Plug Type:
3-Pin BS
3-Pin BS
3-Pin BS
Receiver Capacity: L
6
24
50
Size (W x D x H):
460 x 230 x 510mm
610 x 290 x 640mm
730 x 320 x 700mm
Supply:
230V
230V
230V
Noise level:
79dB(A)
ION AND A
79dB(A)
79dB(A)
S
AC0607S, SAC2410S, SAC5016S Issue 1 09/03/21
Original Language Version
© Jack Sealey Limited
