Composite lightweight housing reduces effects of chill
on operator’s hands. Adjustable speed control on side
of motor housing. Air motor with quality bearings for
smooth and powerful operation. Ideal for sanding down
smaller areas prior to smart repairs or spot refinishing.
Supplied with Ø75mm hook-and-loop pad. Suitable for
the professional workshop.
2. INTRODUCTION & SPECIFICATION
Pad Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75mm
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.3hp
Orbit Size:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3mm
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . . 15000rpm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . 3cfm
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . 88.2dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . 77.2dB(A)
Measured vibration emission value (a): . . . . . 7.19m/s²
Uncertainty value (k): . . . . . . . . . . . . . . . . . . . 2.88m/s²
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5kg
3.1. Air Supply
3.1.1. Ensure the sander trigger is in the "Off" position before connecting to the air supply.
3.1.2. You will require an air pressure of 90psi, and an air flow according to the specifications.
3.1.3.
p
WARNING!
Ensure the air supply is clean and does not exceed 90psi while operating the sander.
Too high an air pressure and/or unclean air will shorten the product life due to excessive wear, and may
be dangerous, causing damage and/or personal injury.
3.1.4. Drain the air tank daily. Water in the air line will damage the sander
and will invalidate your warranty.
3.1.5. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig.1.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.
3.1.7. Keep hose away from heat, oil and sharp edges. Check hoses for wear and make certain that all
connections are secure.
3.2. Couplings
3.2.1 Vibration may cause failure if a quick change coupling is connected directly to the air sander. To overcome
this, connect a leader hose to the sander. A quick change coupling may then be used to connect the
leader hose to the air line recoil hose. See figs.1 & 2.
fig.1
3. PREPARING TOOL FOR USE
p
WARNING! Ensure you read, understand and apply
the safety instructions in Section 1 before use.
4.1. Assembly
4.1.1. Screw the backing pad into the sander spindle, then
tighten with supplied spanner (fig.3B). Apply the
sanding disc, use only discs with speed ratings equal
to or higher than the speed rating of the sander.
DO NOT
use cloth backed sanding discs.
4.1.2. Connect air supply to sander and press the trigger
(fig.3C) to check that the sander is working correctly.
4. OPERATING INSTRUCTIONS
fig.3
fig.2
Original Language Version
SA721.V2 Issue: 2(SP) - 15/01/14
© Jack Sealey Limited
