background image

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH

IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ OR PERSONAL INJURY AND WILL INVALIDATE

THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.

SAFETY INSTRUCTIONS

p

WARNING!

Ensure Health & Safety, local authority and general workshop practice regulations are adhered to 

when using this equipment.

p

WARNING!

Disconnect from air supply before changing accessories or servicing.

3

Maintain the sander in good condition (use an authorised service agent).

3

Replace or repair damaged parts. 

Use genuine parts only. Unauthorised parts may be dangerous and

will invalidate the warranty.

3

Use in suitable, clean and tidy work area, free from unrelated materials. Ensure that there is adequate lighting.

3

Before each use check abrasive for condition. If worn or damaged replace immediately.

3

Ensure the correct abrasive pad size is used.

3

Ensure there are no flammable or combustible materials near the work area.

p

WARNING! 

Always wear approved eye or face and hand protection when operating the sander. 

3

Use face, dust, or respiratory protection in accordance with COSHH regulations. 

3

Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.

3

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie

back long hair.

3

Wear appropriate protective clothing and keep hands and body clear of working parts.

3

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

3

Keep children and unauthorised persons away from the work area.

3

Check moving parts alignment on a regular basis. 

3

Ensure that workpiece is secure before operating the sander. Never hold a workpiece by hand.

3

Check the workpiece to ensure that there are no protruding screws, bolts, nuts, nails, stones, etc.

3

Avoid unintentional starting.

p

WARNING!

Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi. 

3

Keep air hoses away from heat, oil and sharp edges. Check air hose for wear before each use and ensure

that all connections are secure.

3

Prolonged exposure to vibration from this sander poses a health risk. It is the owner’s responsibility to correctly 

assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.

7

DO NOT use the sander for a task it is not designed to perform. 

7

DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.

p

WARNING!

DO NOT sand any materials containing asbestos.

7

DO NOT carry the sander by the hose, or yank the hose from the air supply.

7

DO NOT force, or apply heavy pressure to, the sander. Let the sander do the work.

7

DO NOT place attachments close to your face and do not point at other persons or animals.

7

DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.

7

DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and including

waste wiping or cleaning rags etc.

7

DO NOT carry the sander with your hand on the power lever. 

7

DO NOT direct air from the air hose at yourself or others.

SA32.V2 - 1 - 090904

INSTRUCTIONS FOR:

TWIN PISTON IN-LINE SANDER

Model: SA32.V2

PARTS FOR:

TWIN PISTON IN-LINE SANDER

Model: SA32.V2

Item

Part No.

Description

1

SA32.V2-01

AIR INLET

2

SA32.V2-02

SCREW

3

SA32.V2-03

REAR COVER

4

SA32.V2-04

SPRING

5

SA32.V2-05

O-RING

6

SA32.V2-06

VALVE STEM

7

SA32.V2-07

VALVE PLUG

8

SA32.V2-08

VALVE COLLAR

9

SA32.V2-09

OIL COTTON

10

SA32.V2-10

OIL COTTON

11

SA32.V2-11

GASKET

12

SA32.V2-12

FLAT GEAR

13

SA32.V2-13

RIVET

14

SA32.V2-14

PISTON

15

SA32.V2-15

PISTON RING

16

SA32.V2-16

CYLINDER

17

SA32.V2-17

SCREW

18

SA32.V2-18

SPRING PIN

19

SA32.V2-19

TRIGGER

20

SA32.V2-20

HANDLE

21

SA32.V2-21

SCREW

22

SA32.V2-22

PLUG

23

SA32.V2-23

O-RING

24

SA32.V2-24

PIN

25

SA32.V2-25

SWITCH

26

SA32.V2-26

PALM HANDLE

27

SA32.V2-27

BODY

Item

Part No.

Description

28

SA32.V2-28

FRONT COVER

29

SA32.V2-29

WIRE CLIP

30

SA32.V2-30

RIVET

31

SA32.V2-31

COMPRESSION SPACER

32

SA32.V2-32

FIXED PLATE

33

SA32.V2-33

SCREW

34

SA32.V2-34

FOAM PAD

35

SA32.V2-35

PAD ASSEMBLY (PARTS 29,30,31,32,34,35)

36

SA32.V2-36

RIVET

37

SA32.V2-37

RIVET

38

SA32.V2-38

PAD PLATE

39

SA32.V2-39

LOCKING NUT

40

SA32.V2-40

SIDE GEAR

41

SA32.V2-41

BRASS PLATE

42

SA32.V2-42

SCREW

43

SA32.V2-43

TRANSMISSION GEAR

44

SA32.V2-44

GEAR SHAFT

45

SA32.V2-45

SWITCH GEAR

46

SA32.V2-46

SWITCH SLEEVE

47

SA32.V2-47

PLATE GUIDE

48

SA32.V2-48

SCREW

50

SA32.V2-50

SCREW

51

SA32.V2-51

RIVET

52

SA32.V2-52

PLUG

53

SA32.V2-53

NEEDLE BEARING

54

SA32.V2-54

FRONT GASKET

Issue No:

1

Date Issued: 090904

01284 757500

01284 703534

[email protected]

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

email

01284 757500

01284 703534

[email protected]

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

email

NOTE:

It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: 

No liability is accepted for incorrect use of product. 

WARRANTY: 

Guarantee is 12 months from purchase date, proof of which will be required for any claim. 

INFORMATION: 

For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

Reviews: