5. OPERATING INSTRUCTIONS
4.4. Keep the air hose between the compressor and the air jack as short as possible and install a filter/separator and oiler.
4.5. Drain compressor air tank daily. Water in air line will damage jack.
4.6. Clean the compressor air inlet filter screen weekly.
4.7. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum bore for hose and fittings is 3/8".
4.8. Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.
5.1.
Preparation before use
5.1.1. Oil all moving parts.
5.1.2. If air supply does not have an oiler apply approximately 1ml of air tool oil into the air inlet before first use. Repeat after every 25 lifts.
5.1.3. Connect the supply airline to the air inlet (32). Maximum air pressure 170psi (12 bar).
5.2.
Using the jack
p
p
p
WARNING!
Ensure you have read and understood the Safety Instructions in Section 1 before commencing work.
5.2.1. Position the jack and appropriate extension under the vehicle manufacturers recommended jacking point
(see vehicle handbook).
5.2.2. To raise the jack, move the control valve lever clockwise.
5.2.3. When the vehicle has reached the desired height release the control lever which will automatically return to the hold position. This will
shut off the air flow and hold the jack at the height to which it has been raised.
5.2.4. Place axle stands in position and ensure Section 1 Safety Instructions are strictly applied before performing any task.
5.3.
Lowering the jack
5.3.1. Ensure there are no persons or obstructions beneath the vehicle before lowering, and remove any axle stands.
5.3.2. To lower the jack, slowly and carefully move the control valve lever anticlockwise and the jack will lower in a controlled manner.
5.3.3. Once completely lowered release the control lever which will return to the middle hold position. Remove the jack from under the vehicle.
5.3.4. Turn off the air supply, disconnect the jack from the airline and store the jack, fully lowered, and airline.
30.40, 50.20, 50.30 - 0001 - (1) - 220201
s
s
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair.
p
p
p
WARNING!
Disconnect jack from air supply before changing parts, servicing or performing any maintenance.
6.1.
When the jack is not in use, the ram must be in the lowest position to minimise corrosion.
6.2.
Keep the jack clean and lubricate all moving parts on a regular basis.
6.3.
To check oil level, stand jack, fully lowered, on a level surface. Remove oil filler plug (28). The correct oil level is to the lower edge of
the filler hole.
NOTE:
Use only a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL.
p
p
p
WARNING!
DO NOT
use brake fluid, or any fluid other than hydraulic jack fluid, as this may cause serious damage to the jack
and will invalidate the warranty!
p
p
p
WARNING!
Wear safety goggles.
6.4.
Ensure the air filter located in the air valve is regularly checked and cleaned as necessary.
6.5.
Before each use check for broken, cracked, bent, or loose parts. If any suspect item is found remove jack from service and take
the action necessary to remedy the problem.
DO NOT
use the jack if it is believed to have been subject to abnormal load or shock. Inspect and take appropriate action.
6.6.
Hydraulic oil should be replaced annually to extend the life of the jack.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE JACK.
Air/Hydraulic products are repaired only by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN JACK TO US.
Please telephone us on 01284 757500 to obtain the address and phone number of your local agent. If jack is under guarantee please contact your dealer.
De-commissioning the jack
When jack eventually becomes completely unserviceable, draw off oil into an approved container and dispose of jack and oil according to local regulations.
6. MAINTENANCE
PROBLEM
POSSIBLE CAUSE
REMEDY
Vehicle does not lift.
Air pump operates slowly.
1. Replenish.
1. Use a larger compressor.
2. Clean filter.
1. Hydraulic oil low.
1. Insufficient air supply.
2. Inlet filter blocked.
7. TROUBLESHOOTING
8. DECLARATION OF CONFORMITY
For any other faults contact a service agent.
Declaration of Conformity
We, the sole importer into the UK, declare that the products listed below are in conformity with the following standards and directives.
The construction files for these products are held by the Manufacturer and may be inspected, by a national authority,
upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
Signed by Mark Sweetman
1st March 2001
Air/Hydraulic Trolley Jacks
Models: 30.40, 50.20 & 50.30
93/68/EEC CE Marking Directive
98/37/EC Machinery Directive
Sole UK Distributor,
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500
E-mail:
01284 703534
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required
for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
