NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12 months from
purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on
01284 757525 and leave your full name and address, including postcode.
PROBLEM
POSSIBLE CAUSE
SOLUTION
Excessive noise:
1. Incorrect belt tension.
1. Adjust tension.
2. Spindle is dry.
2. Disassemble spindle/quill and lubricate.
3. Pulley is loose.
3. Tighten pulley.
4. Bearing damaged.
4. Replace the bearing.
Excessive drill wobble:
1. Chuck is loose.
1. Tighten the chuck by pressing it against the table.
2. Bearing or spindle shaft is worn.
2. Replace worn part.
3. Chuck is worn.
3. Replace the chuck.
Drill binds in the workpiece:
1. Feed pressure is too great.
1. Apply less pressure.
2. Belt is loose.
2. Adjust tension.
3. Drill bit is loose.
3. Tighten the chuck jaws with the key.
4. Speed is too fast.
4. Change the speed.
Drill burns or smokes:
1. Speed is too fast.
1. Change the speed.
2. Chips are not discharging.
2. Clean the drill bit.
3. Drill bit is dull.
3. Use a new bit.
4. Lubrication needed.
4. Lubricate while drilling.
5. Feed pressure is too great.
5. Apply less pressure.
Table is difficult to raise:
1. Lubrication is needed.
1. Lubricate with light oil.
2. Rack is bent.
2. Straighten the rack.
7. TROUBLESHOOTING
6.1 Clean the tool after each use. A coat of automobile-type wax applied to the table and column will help to keep the surfaces clean.
6.2 Blow out any dust that may have accumulated in the motor.
6.3 Periodically lubricate the table elevation rack/gear/worm mechanism and the spindle sleeve exterior.
6. MAINTENANCE
5. DRILL SPEEDS
PDME160B-PDME200F - 1 - 151204
Declaration of Conformity
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack Sealey Ltd.
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Quality Machinery.
Signed by Mark Sweetman
15th December 2004
www.sealey.co.uk
01284 757500
01284 703534
Web
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
PILLAR DRILLS WITH DIGITAL VARIABLE
SPEED MODELS: PDME160B & PDME200F
73/23/EEC LOW VOLTAGE DIRECTIVE
89/336/EEC EMC DIRECTIVE
98/37/EC MACHINERY DIRECTIVE
93/68/EEC CE MARKING DIRECTIVE
2600rpm
1350-2100rpm
1190-1350rpm
720-1190rpm
480-720rpm
350-480rpm
300-350rpm
6.4mm
9.5mm
16mm
22mm
31.75mm
41.4mm
50.8mm
4.8mm
6.4mm
9.5mm
12.5mm
19mm
22mm
25.4mm
4mm
5.5mm
8.75mm
12mm
17.5mm
19mm
-
3.2mm
4.8mm
7.9mm
11mm
16mm
20.5mm
-
2.4mm
3.2mm
6.4mm
8.75mm
12.5mm
16mm
-
1.6mm
2.4mm
4mm
6.4mm
9.5mm
12.5mm
-
1.2mm
1.6mm
3.2mm
4.8mm
7.9mm
11mm
14.5mm
0.8mm
1.2mm
1.6mm
3.2mm
6.4mm
9.5mm
12.5mm
WOOD
ZINC
DIECAST
ALUMINIUM
& BRASS
PLASTIC
CAST IRON
& BRONZE
STEEL MILD
&
MALLEABLE
STEEL
CAST &
MED
CARBON
STAINLESS
STEEL
SPEED RANGE