IMPORTANT:
Inflation will only be effective if the connector head is fully fitted and secured onto the valve.
4.3.
We recommend the use of a dial pressure gauge for a definitive reading of tyre pressure.
4.4.
Connect compressor power cables directly to vehicle battery or 12V DC power source. Red Positive (+) clamp to Positive battery
terminal, Black Negative (-) to battery Negative terminal. PLEASE TAKE CARE NOT TO ACCIDENTALLY REVERSE THE POLARITY!
4.5.
Set the target pressure on the compressor LED display by using the UP or DOWN buttons, fig.1. To start the compressor, press the ON
(middle) button, the green operation LED will illuminate. The compressor will automatically turn off when the target pressure is
reached. The gradient reading LED below the target pressure will show progress during inflation.
4.6.
If your target pressure is lower than the existing tyre pressure, when the chuck is connected with power on the gradient gauge will be
completely lit and the compressor will not start operation. Manually deflate the tyre by depressing the valve until the pressure is
below your target, and then complete the above steps.
4.7.
THERMAL PROTECTION
4.7.1.
This compressor is fitted with a high temperature thermal shut off to protect the compressor if it is overloaded. If the unit gets too hot,
it will automatically turn off until it cools down again. When this occurs, the red LED indicator will illuminate showing this condition, fig.1.
The compressor can be restarted once the red LED goes out.
4.8.
AIR FILTER see fig.2
4.8.1.
The compressor has a serviceable foam air filter to prevent debris entering the internal workings. To clean remove the foam pad,
(unscrew end thumb wheel) rinse with mild soapy water. Wait for the pad to completely dry before refitting.
NOTE:
As the delivery pressure increases, the pump delivery volume will decrease.
4.9.
Remove the air hose from the tyre valve. Switch off the vehicle engine. Replace the dust cap onto the valve.
4.10.
A
fter use, disconnect the compressor from the vehicle accessory socket or battery and store it in a safe, dry location.
4.11.
GENERAL INFORMATION
4.11.1. The time it will take to inflate a tyre will depend upon the amount of air required.
4.11.2. S
hould the compressor fail to start when switched on, check the connections and fuse see 4.11.
NOTE:
The compressor may also be used to inflate items such as inflatable dinghies, sports balls, air beds etc. Use the appropriate
inflation nozzle for the item.
CAUTION:
Some items may not indicate pressure required or the maximum pressure. Be careful not to over-inflate.
NOTE:
The pressure gauge is not a calibrated instrument. It is recommended to use an approved dial pressure gauge for a definitive
reading.
4.12.
FUSES
The compressors are protected by an automotive style blade fuse. The fuse is housed in the rubber holder which is part of the supply
lead.
DO NOT
replace the fuse with any not of the same specification as the original.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important
: No Liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Original Language Version
© Jack Sealey Limited
M
AC04D, MAC05D Issue:1 - 04/05/20
fig.1
fig.2