manualshive.com logo in svg

Seagull cassutt 3M Racer, Assembly Manual, Page: 21 / 23

Share
Download
Seagull cassutt 3M Racer Assembly Manual Download Page 21

www.seagullmodels.com

21

INSTALLING THE BATTERY-RECEIVER.

 

  

  

  3)   Route the antenna in the antenna tube

inside the fuselage and secure it to the bot-
tom of fuselage using a plastic tape.

APPLY THE DECALS.

1)  If all the decals are precut and ready to
stick. Please be certain the model is clean and
free from oily fingerprints and dust. Position
decal on the model where desired, using the
photos on the box and aid in their location.

2)  If all the decals are not precut, please use
scissors or a sharp hobby knife to cut the
decals from the sheet. Please be certain the
model  is clean and free from oily fingerprints
and dust. Position decal on the model where
desired, using the photos on the box and aid
in their location.

Required Parts

•

Fuselage assembly

•

Receiver

•

Receiver battery

Required Tools and Adhesives

•

Phillips screwdrive

Wing tube.

 1)  Attach the aluminium tube into fuselage.

ATTACHMENT WING-FUSELAGE.

    Locate the items neccesscery to install the
wing  set to fuselage .

Required Parts

•

Fuselage assembly

•

Wing assembly

•

Wing tube

•

M4x12mm socket head screw(2)

•

M4 washer(2)

Required Tools and Adhesives

•

Phillips screwdrive

•

30-minute epoxy

•

Drill bit 3mm

•

Drill

2x6mm

  2)  Insert two wing panels as pictures below.

 

 1) Plug the five servo leads and the switch

lead into the receiver.  Plug the battery pack
lead into the switch also.

     2)  Wrap the receiver and battery pack in

the protective foam rubber to protect them
from vibration.

Summary of Contents for cassutt 3M Racer
























Reviews:

No comments