GENERAL DIRECTIONS
Before the installation takes place, make sure that the product has not been damaged in the parts which could compromise its assembling or
safe working. Check the packing stuff and if you have the right fixing materials. On the check we refer to the instructions available on each
model.
Make sure that the structure on which you are fixing the product is sufficiently strong for strains (e.g. against the wind force on the gate or
product surface) and hold the anchorage firmly.
SEA S.r.l. forbids installation on unsafe, fragile or crumbling walls which can't hold strains and do not provide an effective sustain.
Consult a technician if you are not sure about the wall strength.
The place where the product has to be installed must be compatible with the product itself. Avoid: place excessively icy on winter times; direct
exposure to corrosive agents or similar. It is not possible to make a list of all the possible negative conditions. Anyway, pay attention on where
you are placing the system.
Further characteristics of the installation place (e.g. minimum spaces, distances to be kept) are available on the instructions of each product
and sector regulation normative.
Further information for a correct installation (e.g. schemes of electrical connections) are usually available on the installation instructions of each
product or enclosed schemes.
Product installation has to be executed by technicians only.
All the systems must be installed by sector technicians who will issue a document as provided by law.
Before connecting the electrical power to the network, make sure that engine data and distribution grid are the same and that electrical power is
compatible with the maximum power.
The product electrical safety is reached only when it is connected to a efficient grounding as provided by safety law. Meeting the just stated
requirement is very important; if doubtful refer to a qualified technician. SEA can't be hold responsible for damages being caused for no
grounding.
It is not allowed the installation in presence of children or unauthorised person.
SEA forbids every kind of adjustment or modify of product anchorage points or product itself if not authorised.
Extra anchorages and adjustments required have to be directly shown to SEA with drawings attached of the required modification.
Only after eventual SEA written authorisation the product installation is possible. Without authorisation SEA is not responsible for failing
assemble or product dysfunction.
A faulty installation can be cause of damage to people, animals and things which SEA can't be claimed responsible for.
Further conditions and details are direclty reported in the UNI EN 13241-1 regulation to which to refer in eventual, special cases.
PLEASE NOTE
:
Packing stuff such as: plastic bags, foam polystyrene, screws etc. must be kept out of children reach ever since they could be
dangerous
.
FIRST SETTING UP AND CONTROLS
Make sure that product has not been damaged while being installed so to work poorly and unsafely.
Check the detectors, limit switches control and safety devices. They must be well installed and working.
If you are not sure about safety devices performance, start the system and be very careful.
During this first step, the installer has to be very close to the controls. If the system doesn't work perfectly the installer has to stop it immediately.
The installer is the only authorised person to use the product. Non authorised people are to be taken away from dangerous zone. The installer
will work on the commands provided by SEA only.
As a precaution it is useful that a second person stays five metres far from the product being so able to watch the installer and helpful in case of
danger.
Before starting the first operation keep runners, strokes, hinges and element moving spaces clear of obstacles.
On the first starting keep children, animal, non authorised person away.
Don't set any command if doubtful, don't modify any command provided.
Don't touch any electrical part if some part of your body is either wet or humid.
In case of dysfunction search the troubling causes by following installation instructions and solve the problems.
If it shouldn't prove to be enough, assemble the product again following the instructions available in your just bought product.
If a further assembling proved to be useless, refer to factory technicians.
EXPLOITABLE MODES
SEA products have been designed and built for buildings and whatever needing automatic systems for doors, gates, leaves and barriers.
Product opening and closing must be carried out by runners and strokes provided by SEA.
SEA, forbids whatsoever modification of forces acting on the product (e.g. by adding weight to leaves, changing panels or glasses, varying
motor power).
The building owner is responsible for the instruction and information of eventual users.
SEA is not responsible for accidents due to users poor instruction. The product has not to be used by children and non authorised person.
The use is forbidden on occasion of ice and whatever situation could damage the product (e.g. during a thunderstorm).
The use of the product is forbidden if it is badly preserved or the safety device doesn't work properly (e.g. the product is too old).
The use of the product is also forbidden in presence of whatsoever chemical agent compromising the product and user safety (e.g. chemical
agents damage product characteristics and user clearness of mind as well).
Before starting the first operation keep runners, strokes, hinges and element moving spaces clear of obstacles.
Keep clear of the manoeuvring area, hinges and mechanic organ moving.
Put out a clear warning notice if the product is remote controlled.
PLEASE NOTE!
Don't stick any object to the product in its parts. Product surfaces and whatever part have to be kept free of additional
obstruction, weights, limit switches that haven't been provided in the installation.
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
46/64
REV 00 - 02/2010
cod. 67410329