background image

6

PRECAUTIONS

SEA  operators  have  been  created  for  the 
automation of gates used by vehicles only. Be 
aware  to  avoid  the  crossing  of  the  gate  path 
because  it  is  very  dangerous  for  pedestrians 
(fig.8). 
Make  sure  that  no  person  could  activate  the 
automation or act on it from the outside (fig. 9) 

WARNING SIGNS

Install the warning signs, on each side of the 
gate and in a visible zone

 

which informs the 

pedestrians  about  the  danger  they  run  when 
passing or resting in the environment of the gate

Important:  
For a higher security, SEA advices to install 
infrared photocells

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

1/2”

1/4”

5”

Fig. 7

!

WARNING

Moving Gate Can Cause
Serious Injury Or Death 

-  KEEP CLEAR !  Gate may move at any 
time without prior Warning.
-  Do not let children operate the gate or 
play in the gate area.
-  This entrance is for vehicle only.
Pedestrians must use separate entrance

TYPE OF INSTALLATION

A  front  installation  is  the  right  and  only     
possible installation, it is highly recommended 
to  install  two  security  gate  stops  on  the  two 
extremities of the rail to prevent the gate from 
derailment (fig. 11).

GATE ARRANGEMENT 

The first thing to check is that the gate is in good running order as follows:

a)

 The gate is rigid and straight and runs smoothly throughout its travel.

b)

 That the inferior sliding guide-rail is perfectly straight and horizontal to avoid a derailment of the gate (fig. 1); 

furthermore it must be free of irregularities and foreign bodies which could obstruct  the normal run of the gate 
(fig. 2 - 3).

c)

 That the upper guides are not fixed (fig. 4) but  furnished with  rollers 

d)

 That the distance between  the end of the gate (in maximum opening position) and the eventual wall must 

be at least of 5 inches (fig. 7) which allow the sliding of the gate without difficulties (fig. 5 and 6).

e)

 The lower support wheels have sealed bearings or grease points.

f)

  The top guide must be manufactured and installed so that the gate is perfectly upright.

g)

 Physical gate stops must be fitted to prevent the gate coming out of its guides and track.

Fig. 8

GATE WARNINGS AND PRECAUTIONS

Fig. 9

Fig. 10

!

WARNING

Moving Ga

te Can Cause

Serious Injur

y Or Dea

th 

-  KEEP

 CLEAR !  Gate may move at any time 

without prior W

arning.

-  Do not let children operate the gate or play in 
the gate area.
-  This entrance is for vehicle only

.

   Pedestrians must use separate entrance

Fig. 11

Over-Travel Stop

Over-Travel

Stop

Summary of Contents for ORION BOX 24V

















Reviews: