SEA LEPUS 1800 Fitting And Connection Instructions Download Page 12 | Manualshive

Page: 12 / 12

SEA LEPUS 1800 Fitting And Connection Instructions Download Page 12

Sistemi elettronici
di Aperture Porte e Cancelli

11.

(Fig. 26)

CABLE LAYOUT

2x

5

1,

2x ,5

1

3x1,5

1x1,5

1 5

2x ,

1

3x ,5

1,5

2x

x1

3

,5

6 1,5

x

x

8 1,5

1xRG58

1

2

3

4

11

5

6

7

8

9

10

1) LEPUS operator
2) Left photocell
3) Right photocell
4) Pneumatic safety edge
5) Key switch
6) Flashing warning lamp
7) Radio receiver

12. RISK EXAMINATION

The points pointed by arrows in Fig. 27 are potentially
dangerous. The installer must take a thorough risk examination
to prevent crushing, conveying, cutting, grappling, trapping so
as to guarantee a safe installation for people, things and animals
(

)

Re. Laws in force in the country where the installation has been

made.

8) Antenna
9) Warning notice
10)Electronic control unit
11) 16A- 30mA differential switch

NOTICE

SEA s.r.l can not be deemed responsible for any damage or
accident caused by product breaking, being damages or
accidents due to a failure to comply with the instructions herein.
The guarantee will be void and the manufacturer responsibility
(according to Machine Law) will be nullified if SEA Srl original
spare parts are not being used.

This is a quotation from the GENERAL

DIRECTIONS that the installer must read carefully before
installing. Packaging materials such as plastic bags, foam
polystyrene, nails etc must be kept out of children’s reach as
dangers may arise.

The electrical installation shall be carried out by a professional
technician who will release documentation as requested by the
laws in force.

Fig. 26

Fig. 27

DECLARATION OF CONFORMITY

SEA declares under its responsibility that the products

Lepus 800, Lepus 800 CONTINUO, Lepus 1200, Lepus 1800,
Lepus 2000 THREE-PHASE

meet the essential requisites provided for by the following
European Directive and following changes:

89/392/CEE (Machine Directive)
89/336/CEE (Electromagnetic Compatibility Directive)
73/23/CEE (Low Tension Directive)

SAFETY PRECAUTIONS:

All electrical work should conform to current regulations. A 16 A
0,030 A differential switch must be incorporated into the source
of the operators main electrical supply and the entire system
properly earth bonded. Always run mains carrying cables in
separate ducts to low voltage control cables to prevent mains
interference.

INTENDED USE:

The Lepus operator has been designed to be solely used for the
automation of sliding gates.

SPARE PARTS:

To obtain spare parts contact:

SEA s.r.l. -Zona Ind.le, 64020 S. ATTO Teramo Italia

SAFETY AND ENVIRONMENTAL COMPATIBILITY:

Don’t waste product packing materials and/or circuits.

When being transported this product must be properly
packaged and handled with care.

MAINTENANCE AND OUT OF SERVICE:

The decommission and maintenance of this unit must only be
carried out by specialised and authorised personnel.

NOTE: THE MANUFACTURER CAN NOT BE DEEMED
RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED
BY IMPROPER USE OF THIS PRODUCT.

SEA

reserves the right to do changes or variations that may be

necessary to its products with no obligation to notice.

REV 04 - 09/2005

Check the oil level (trasparent cap placed on the side of
the bell)

Change the oil

Check the release function

Check the clutch function on the gate

Check the distance between the pinion and the rack

Check the wear condition of the pinion and of the rack

Check the fixing screws

Check the integrity of the connection cables
Check the function and the limit switch condition in
opening and closing and the related plates

PERIODICAL MAINTENANCE

Annual

4 years

Annual

Annual

Annual

Annual

Annual

Annual

Annual

All the above described operations must be made exclusively by
an authorized installer.

cod. 67410012

«
...
10
11
12

Summary of Contents for LEPUS 1800













Reviews:

No comments