background image

GATE WARNINGS 

The first thing to check is that the gate is in good running order as 
follows:

A. 

The gate is rigid and straight and runs smoothly throughout its travel.

B. 

The length of each leaf is not over 6,6 feet (ALPHA 200), 10,8 feet 

(ALPHA 330).

C.

The weight of each leaf is not over 440 Pound (ALPHA 200), 661 

Pound (ALPHA 330).

D.

The hinges are hardly anchored and are able to support the torque of 

the operator; they do not have irregular movements and/or any friction 
during the whole movement of the leaf.

PRECAUTIONS

ALPHA has been created for the automation of gates used by vehicles 
only. Be aware to avoid   the crossing of the gate path because it is very 
dangerous for pedestrians (fig. 4).

Install the warning signs, on each side of the gate and in avisible 
zone

Important:
For a higher security, SEA advices to install infrared photocells.

 

which informs the pedestrians about the danger they run when 

passing or resting in the environment of the gate (fig. 5). 

GATE WARNINGS AND PRECAUTIONS

ALPHA

 

- Install the operator in the correct position

- Do not Install the front bracket in a weak part of the gate

- Not for pedestrian opening

8

Fig. 4

Fig. 3

Fig. 2

Fig. 5

International registered trademark n. 2.777.971

REV 03 - 06/2009

Fig. 1

Summary of Contents for ALPHA 330 STANDARD





















Reviews: