START (N.O.)
An impulse given to this contact opens and closes the automation depending onthe selected logic It
can be given by a key switch, a keypad, etc. To connect the other devices refer to the related
instructions leaflets. (ie. loop detectors and proximity switches)
Note1
: In DEAD MAN logic it is necessary to keep pressed the Start for the opening of the
automation.
PEDESTRIAN START (N.O.)
To obtain a partial opening connect the key-button wires as in the figure. It is possible to connect other
command devices (push button board, radio receiver, keypad).
Note1: The contact for partial opening is a N.O. Contact (Normally open)
Nota2: In manual logic it is necessary to keep pressed the Start Ped. To re-close the automation.
STOP (N.C.)
The pressure on this button immediately stops the motor in any condition/position. A start command
is needed to re-start the movement.
After a stop the motor always re-starts in closing.
Notice
: If the stop button is not used it is not necessery to close the N.C. contact between the clamps
1 and 2 of M9 as the absence of the stop is revealed during the selflearning phase of the times.
N.O.
-
1
2
1
2
M7
N.C.
-
1
2
1
2
M9
N.O.
-
1
2
1
2
M6
Can be activated through the Jolly programmer or modifying either the PHOTO entry or the PEDESTRIAN entry.
In both cases it’s a N.O. contact which provoques the opening of the automation keeping it open until it is
activated. When it’s released, the gate attends the set pausing time and executes the reclosing.
Note2
: When activated on the pedestrian entry, the pedestrian will be disabled also on the radio transmitter.
Note3
: In case of intervention of a security device during the timer (Stop, Ammeter, Edge), to restore the
movement it will be necessary to give a start impulse.
Note4
: In case of no power supply with open gate and active Timer the control unit will restore its use, otherwise
if during restore of the power supply the TIMER is not activated it will be necessary to give a start impulse for
the reclosing.
JOLLY OPTIONS
Activation TIMER
: this entry can be transformed into TIMER (See TIMER)
Pedestrian opening space
: Linearly adjustable from 30% to 100%.
START - STOP - PEDESTRIAN START - ANTENNA -
PHOTOCELL
Photocell 1 Connection
When the ray of the photocell is crossed, and the automation is in phase of closing it reverses its
movement.
Note: If the photocell is not connected, put a jumper between the clamps 1 and 2 of (M10).
+ = 24V - = 0V C = Connection Com = Common
The photocell is also usable in connection with BUS photocells.
JOLLY OPTION
TIMER
M2
5
M
M6
M7
M9
M 0
1
USER 1 - 24V
1
2
1
2
M5
GND
1 2
1 2
M2
RX
TX
Co
m
N. .
C
1
2
1
2
M10
-
+
-
+
-
+ 24V
24Vaux max 200 mA
JOLLY OPTION
Through the Jolly programmer it is
possible to choose when having
tension on the 24Vaux output. The
options are: always, only during
opening, only during cycle, only
before opening or only during pause.
JOLLY OPTIONS
FOTOCLOSE activation
: If activated when the photocell is crossed during the pause, the
gate interrupts the pause and immediately closes again.
TIMER activation
: If the entry is activated it turns into a N.O. entry with TIMER function (see TIMER).
Fotoopen activation:
If activated the photocell blocks the movement as long as it’s busy,
when
released it opens
.
FOTO PARK activation
: in opening it is not active; when during the pause ”closing with photo” and
“automatic closing” are activated it commands the closing when released, otherwise it’s not active; in
closing it stops the movement as long as it is busy, when released the closing continues.
FOTO STOP activation
: When activated before the opening the photocell blocks the automation as
long as it is busy, during the opening it will be ignored. In closing the intervention of the photocell causes
the reopening.
ANTENNA
Connect the antenna
as in the figure.
9
International registered trademark n. 2.777.971
67411071
REV 01 - 05/2011
