background image

USER 1 - 24V

Allows to regulate and to visualize 
the sensitivity   of the anti-sqeezing 
for single opening direction With   
value 100% the gate in presence of 
obstacle will reverse the movement   
after 5 seconds.

Screen 12

Balanced edge         on/off ( In ON it is necessary to insert in series to the edge 
                                 contact a  8K2 Ohm resistance)

24V aux                     During cycle/in opening/in closing/in Pause/Always 

N°8

Mot. rev.                    ON/OFF Allows to exchange contemporarily the limit switch 
                                 and the motor rotation direction without disconnecting the 
                                  wires

N°9

Start on pause            ON/OFF If on  ON with autom. Clos. on ON  a start 
                                   impulse provoques the immediate re-closing of the autom.

N°10

Autom. clos.               ON/OFF If on ON at the end of the set pause 
                                   the gate re-closes automatically 

18

Normal

:

1 Flash/s in opening
2 Flash/s in closing
On in pause 

Control lamp

: the alarm signals 

remain until they are eliminated 

 

Continuous

: flashes always also 

when gate is not in movement 

Allows to decide when having power 
supplied the exit 24V Aux.

Note:

 After this operation it is 

necessary to switch off the power 
supply of the motors and to repeat 
the selflearning of the times. If the 
motor is not syncronized with the 
limit switch, during selflearning the 
automation stops on the first limit 
switch it recognizes without 
completing the selflearning of the 
times. In that case it will be 
necessary to switch off the power 
supply again, to manually exchange 
the wires of the motor and to repeat 
the selflearning. 

PROGRAMMER JOLLY PARAMETERS ADJUSTMENT

NOTE

: For the respect of the valid European ruels on the safety of the electric gates, it is recommended to not adjust the 

parameters 

torque   Max 1

 and 

torque Max 2

 on the value 100%.

Screen 10

Accelerat.                  [0÷100]% (inclination of the ramp of acceleration)  

Decelerat.                  [0÷100]% (inclination of the ramp of acceleration) 

Pedestrian op.           [30,50,100]% (percentage pedestrian opening)

It allows to regulate the duration of 
the acceleration of the motors on 
the start If on 100% the gate will   
immediately depart at the max. 
adjusted speed

It allows to regulate the duration of 
the deceleration of the motor at the 
end of opening and closing. If on 0% 
the gate won't effect the phase of 
deceleration.

Screen 11

Torque op. M1            [10÷100]% (max. current of the motors)

Torque clo. M1            [10÷100]% (max. current of the motors)

Anti-intrusion              on/off (in ON it implicates the presence of a contact N.C. 
                                   On the limit switch that, if freed, forces the motors in closing       

Pre- flashing              on/off (activation of the pre-flashing) 

Autotest photo.          on/off (activates autotest photocell)

Max cycle                  0÷100000 (indicates the number of cycles after which it is  
                                  necessary to follow up the maintenance)

Warning lamp            Normal/Control/Continuous

Screen 13

Screen 14

Photo/Timer               ON/OFF  On ON the PHOTO entry becomes TIMER 

Clos. Photo                ON/OFF  On ON if the photocell is occupied the gate 
                                  recloses interrupting the pause                                

Ped/Timer                  ON/OFF  On ON  the PED entry becomes TIMER                   

Screen 15

Screen 16

List of events            Shows the last 10 events on the control unit 

Diagnostic 10 last events

Reverse stroke          on/off (Disabled)
Posit. recover            0%  100%

Allows to optimize the point of 
slowdown beginning   in case of 
inversion of the motion and in 
function of the weight of the gate

Foto                           closing/opening/stop/park

For the functions Fotoopen, 
Fotostop, Fotopark, see page 9.

International registered trademark n. 2.777.971

    

67411071 

REV 01 - 05/2011

Summary of Contents for 2300A24

























Reviews: