Sea-doo LRV 5688 Operator'S Manual Download

Page: 57 / 71

Pre-Season Preparation Chart

NOTE:

It is highly recommended that the dealer perform the annual safety in-

spection and factory campaigns in addition to the pre-season preparation all at
the same time.

Before installing new spark plugs, it is suggested to burn the excess BOM-

BARDIER LUBE lubricant or equivalent by starting the engine using the old
spark plugs.

Safety item covered in the annual safety inspection.

OPERATIONS

TO BE PERFORMED BY

Lubrication/corrosion protection

OPERATOR

Battery condition/charging and reinstallation

DEALER

Battery, starter connections and routing

DEALER

Spark plug replacement

OPERATOR

Jet pump oil inspection

DEALER

Propulsion system inspection

DEALER

Oil filter replacement

DEALER

Fuel tank straps

OPERATOR

Oil tank straps

OPERATOR

Oil injection tank filling

OPERATOR

Flame arrester inspection

DEALER

Fuel filter replacement

DEALER

Fuel line condition

DEALER

Filler neck, fuel tank and fuel cap condition

DEALER

Check valves, fasteners,

fuel system pressurization

DEALER

Throttle

and choke cable inspection/adjustment

DEALER

Oil injection pump adjustment and bleeding

DEALER

Engine ignition timing

DEALER

Carburetor adjustment

DEALER

Steering system adjustment/inspection

DEALER

Reverse cable adjustment

DEALER

Inspection of bailer pick-ups

DEALER

Inspection of cooling system hoses

DEALER

Monitoring beeper

DEALER

Digitally encoded security system

DEALER

smo2000-001b.fm Page 55 Tuesday, May 4, 1999 1:20 PM

www.SeaDooManuals.net

Summary of Contents for LRV 5688






































































Search results

Summary of Contents for LRV 5688

Reviews:

Related manuals for LRV 5688

Brands by name

Popular brands

Sea-doo LRV 5688, Operator'S Manual

Search results

Summary of Contents for LRV 5688

Reviews:

Related manuals for LRV 5688

Brands by name

Popular brands