Sea-doo 2004 GTI Operator'S Manual Download Page 59 | Manualshive

Page: 59 / 130

Sea-doo 2004 GTI Operator'S Manual Download Page 59

58

1. Shift lever in neutral position

1. Reverse gate in middle position

To obtain reverse, pull shift lever com-
pletely. The reverse gate will be in down-
ward position, directing all the thrust to-
ward the front of the watercraft.

1. Shift lever in reverse position

1. Reverse gate in downward position

NOTE:

To obtain maximum efficiency

and control from the reverse, increase
engine speed to slightly above idle.
Too much RPM will create water tur-
bulence and reduce reverse efficiency.

In reverse position, turn the handlebar
in the same direction that you want to
move the rear of the watercraft.

For example, to steer the rear of the wa-
tercraft to the left side, turn the handle-
bar to the left side.

F17L0BZ

1

1

F17J01Y

F17L0CZ

1

1

F17J02Y

F18J08Y

smo2004-002a.book Page 58 Thursday, August 21, 2003 2:54 PM

www.SeaDooManuals.net

«
...
57
58
59
60
61
...
»

Summary of Contents for 2004 GTI



































































































































Reviews:

No comments