manualshive.com logo in svg

Sea-doo 2004 GTI, Operator'S Manual, Page: 117 / 130

Share
Download
Sea-doo 2004 GTI Operator'S Manual Download Page 117

117

Neither the distributor, any Bombardier dealer nor any other person has been authorized to
make any affirmation, representation or warranty regarding the product, other than those
contained in this limited warranty, and if made, shall not be enforceable against Bombardier.
Bombardier reserves the right to modify this warranty at any time, being understood that such
modification will not alter the warranty conditions applicable to the products sold while this
warranty is in effect. 

8. TRANSFER

If the ownership of a product is transferred during the warranty coverage period, this warranty
shall also be transferred and be valid for the remaining coverage period provided that
Bombardier is notified of such transfer of ownership in the following way:

a) The former owner contacts Bombardier (at the phone number provided below) or an

authorized Bombardier dealer and gives the coordinates of the new owner; or

b) Bombardier or an authorized Bombardier dealer receives a proof that the former owner

agreed to the transfer of ownership, in addition to the coordinates of the new owner.

9. CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this Bombardier limited warranty,
Bombardier suggests that you try to resolve the issue at the dealership level. We recommend
discussing the issue with the authorized dealer’s service manager or owner.
If the issue has not yet been resolved, please submit your complaint in writing or call the
appropriate number below:

© 2003 Bombardier Inc. All rights reserved
®, ™ Registered trademarks of Bombardier Inc. or its subsidiaries. 

In Canada:

BOMBARDIER INC.
RECREATIONAL PRODUCTS

CUSTOMER ASSISTANCE CENTER
VALCOURT QC J0E 2L0
Tel: (819) 566-3366

In USA:

BOMBARDIER MOTOR
CORPORATION OF AMERICA

CUSTOMER ASSISTANCE CENTER
7575 BOMBARDIER COURT
WAUSAU WI 54401
Tel: (715) 848-4957

smo2004-002a.book  Page 117  Thursday, August 21, 2003  2:54 PM

www.SeaDooManuals.net

Summary of Contents for 2004 GTI



































































































































Reviews:

No comments