manualshive.com logo in svg

Sea-Bird Electronics SBE 63, User Manual

Share
Download
Sea-Bird Electronics SBE 63 User Manual Download Page 36

Manual revision 005 

Section 6: Troubleshooting 

SBE 63 

36 

Cause/Solution 3 (SeaCATs only)

: A data file with nonsense values may be 

caused by incorrect instrument configuration of the SeaCAT (SBE 16

plus

 V2,  

16

plus

-IM V2, or 19

plus

 V2): 

•

 

Bad data may be caused by incorrect setup in the CTD. Send 

GetCD

 or 

DS

 

to the CTD

 to verify the CTD setup (SBE 63 is enabled for the  

RS-232 auxiliary sensor channel). 

•

 

Bad data may be caused by incorrect configuration in the instrument 

.xmlcon configuration file, and/or incorrect calibration coefficients in the 

instrument configuration file. Verify the settings in the configuration file. 

 

 

Note: 

Each SeaCAT CTD is shipped with a 

configuration file that matches the 

configuration of the instrument 

(number and type of auxiliary 

sensors, etc.) and includes the 

instrument calibration coefficients. 

Summary of Contents for SBE 63















































Reviews:

No comments

Brands by name

Popular brands

Load more brands