Sea & Sea MDX-40D Instruction Manual Download Page 3

E-2

For safe handling of the product, please read the following precautions 
carefully before use.

WARNING

z

Keep out of reach of children to prevent accidental ingestion. If swallowed, seek 
medical advice immediately.

CAUTION

z

Carefully observe the instruction manual for the compatible camera for this product 
before use.

z

Unauthorized disassembling and/or modification could result in malfunction or 
flooding, and void product warranty. Take the product to a SEA&SEA authorized 
service center for repair or inspection.

z

Should you notice smoke or an unusual smell coming from the product, turn it off 
and remove the batteries immediately, taking care to avoid burns. Continued 
operation could result in injury. After removing the battery, take the product to a 
SEA&SEA authorized service center for inspection.

z

Discontinue use and turn the product off immediately should you notice flooding or 
leakage.

z

When the product is flooding, interior pressure may build up. Please be careful when 
opening the product as water may spurt out or the cap may open explosively and 
cause injuries.

z

The product has been constructed with an airtight seal. When packing the product 
for airplane travel, do not seal-up the product to alleviate pressure build up due to 
atmospheric changes.

z

Do not open the product in a wet or sandy environment. Protect the interior from 
moisture and debris in order to prevent malfunction or flooding.

z

Avoid strong shocks/impacts or excess stress to prevent malfunction, damage or 
breakdown. Make sure that the product has been securely mounted to other 
products in order to prevent injury, fall or missing.

z

Do not rest heavy weight on the product. It might deform the outer casing, damage 
internal parts, make the waterproofing fail, or result in fire or electric shock.

z

Please note that some marks may be left on the camera scraping against the dials 
or gears of the housing.

z

Handle the product carefully so as not to scratch the front port, the lens, the flash 
window or the finder.

Safety Precautions

Failure to heed the precautions listed below could result in serious 

consequences. To prevent injury or damage to yourself and/or others, 

please observe the precautions as they contain highly important 
information related to personal and product safety.

WARNING 

Situations that could result in severe injury or death. 

CAUTION

Situations that could result in property damage or 
personal injury. 

Summary of Contents for MDX-40D





















Reviews: