background image

 

 

EC Declaration of Conformity 

This  Product   has  been  designed  and  manufactured  in  accordance  with  the below 
referenced Standards and complies with all essential requirements of the Directives listed 
below.  

 

Directives:  

2014/35/EU 

of the European Parliament and of the Council of 26 February 2014 on 

the harmonization of the laws of the Member States relating to the making available on the 
market of electrical equipment designed for use within certain voltage limits. 

2014/30/EU 

The Electromagnetic Compatibility Directive and its amending directives. 

2011/65/EU 

of  the  European  Parliament  and  of  the  Council  of  8  June  2011  on  the 

restriction  of  the  use  of  certain  hazardous  substances  in  electrical  and  electronic 
equipment. 

 

Standards: 

EN  55011  2009  +  A1:  2010, 

Product  family  standard  for  Industrial,  Scientific  and 

Medical (ISM) equipment. 

EN  61010-1:2010 

Safety  Requirements  for  Electrical  Equipment  for  Measurement, 

Control and Laboratory Use –

 

Part 1: General Requirements 

EN  61326-1:2013 

Electrical Requirements for Electrical Equipment for Measurement, 

Control and Laboratory Use –

 

Part 1: General Requirements 

 

Summary of Contents for PPS-2RM-B
















Reviews: