background image

Security Door Controls

3580 Willow Lane, Westlake Village, CA 91361-4921  •   (805) 494-0622  •  Fax: (805) 494-8861
www.sdcsecurity.com  •  E-mail: [email protected]

The EntryCheck

incorporates all 

the logic necessary to control a 
single door.  All Unit Programming 
is performed by using the built-in 
keypad.  Proximity cards, key fobs 
and PIN entries can be added and 
deleted with the keypad using the 
master code or programming card.  
The lock relay and alarm relay 
outputs can be set for 1-99 
seconds.  

CHOICE OF ENTRY MODE

The SDC EntryCheck

provides a 

choice of three programmable entry 
modes:

•   Proximity Reader Only  
•   Proximity Reader or PIN Code
•   Proximity Reader and PIN Code

WALL OR GLASS MOUNTED

The weather resistant unit is easily 
surface mounted to the wall either 
inside or outside.  An optional glass 
mounting kit is available.  When the 
EntryCheck

is mounted to the 

interior side of a glass sidelight or 
store front, the proximity reader may 
be activated from the exterior 
through the glass.

FEATURES

•   Up to 500 Cards and/or PIN Codes

•   Choice of three entry modes:
    Proximity Reader only
    Proximity Reader or PIN Code
    Proximity Reader and PIN Code

•   Up to 6 inch (152 mm) reader range

•   Add / change / delete cards and         
    PINs

•   Programmable door unlock 
    time from 1 - 99 seconds

•   Tamper alarm and reader/PIN 
     lockout 

•   Request-To-Exit input

•   Two outputs, lock relay and 
     alarm relay

•   LED and audible tone for 
    operation ease.

•   Weather resistant

ORDERING INFORMATION
950C

 Prox / PIN reader w/10 cards

950K

 Prox / PIN reader w/10 key fobs

C10

Ten SDC prox cards

K10

Ten SDC key fobs 

950GL-KIT

 Interior glass mounting kit

TR12

 12VDC Plug-in power supply with 

AC ground and two fused outputs.  
Access control output: 150 mA filtered / 
regulated.  Lock output: 780 mA filtered.

USER INFORMATION

To open door using card and PIN
     Present Card (LED flashing 

red

)

     Enter PIN (LED 

green

)

To open door using PIN only
     Enter PIN number (LED 

green

)

To open door using card only
     Present card to reader (LED 

green

)

INSTALLATION/PROGRAMMING INSTRUCTIONS

950 ENTRYCHECK

Any suggestions or comments to this instruction or 

product are welcome.  Please contact us through 

our website or email [email protected] 

P:\INSTALLATION INST\Access Controls\INST-950\INST-950.vsd     REV G     0605     Page 1

Summary of Contents for 950 ENTRYCHECK







Reviews: