Scotsman SLE400R User Manual Download Page 19

Service Diagnosis:

SYMPTOM

POSSIBLE CAUSE

PROBABLE FIX

No ice is made, nothing operates

Unit off, due to no power

Restore power

Unit off, due to ICE/OFF/WASH
switch in OFF position

Switch ICE/OFF/WASH switch to
ICE

Unit off, due to bin thermostat
closed

Check temperature at bin
thermostat bracket, if warmer than
40

o

F., thermostat should be

open. Adjust/replace thermostat.

Unit off, due to high pressure cut
out open

Check fan motor.

No ice, compressor off

No cooling due to compressor not
operating

Check compressor for voltage,
continuity, and operation. Check
starting components. Replace if
found to be faulty.

If no voltage, check contactor,
replace if coil or contacts open.

Check temperature of
compressor, if hot may be lack of
refrigerant, defective TXV or
compressor

Unit off, due to low pressure
(pump down) control open.

Check liquid line valve coil for
power and/or continuity

No ice is made, compressor is
operating

No water due to water turned off.

Reconnect water supply

No water due to water filter
plugged.

Replace water filter

No water due to strainer screen
plugged

Clean out inlet screen

No water due to inlet water valve
will not open

Replace valve

Water in reservoir, but no water
over evaporators

Water pump does not work,
replace pump

No cooling at evaporator due to
hot gas valve leaking thru

Replace hot gas valve

No cooling at evaporator due to
fan not turning

Check & replace fan motor.

Fan and pump do not have
power; hot gas valve opens and
closes.

Coil or relay open, replace relay.

No cooling at evaporator due to
dirty condenser

Clean condenser

No cooling due to compressor not
pumping

Check system pressures, replace
compressor if not pumping

SLE400R

January 1995

Page 19

Summary of Contents for SLE400R

























Reviews: