background image

N0922L, N1322L, F1222L, F1522L

D Series Remote Low Side User Manual

October 2014

Page 3

Installation:

This machine is designed to be used indoors, in a 

controlled environment. Operation outside the limits 

listed here will void the warranty.

Air temperature limits

Minimum 

Maximum

Ice maker 

50

o

F. 

100

o

F.

Water temperature limits

Minimum 

Maximum

All models 

40

o

F. 

100

o

F.

Water pressure limits (potable)

Minimum 

Maximum

All models 

20 psi 

80 psi

Voltage limits

Minimum 

Maximum

115 volt 

104 

126

Minimum conductivity (RO water)

• 

10 microSiemens / CM

Water Quality (ice making circuit)

• 

Potable

The quality of the water supplied to the ice machine 

will have an impact on the time between cleanings 

and ultimately on the life of the product. Water can 

contain impurities either in suspension or in solution. 

Suspended solids can be filtered out. In solution 

or dissolved solids cannot be filtered, they must be 

diluted or treated. Water filters are recommended 

to remove suspended solids. Some filters have 

treatment in them for suspended solids. Check with a 

water treatment service for a recommendation.

RO water. This machine can be supplied with Reverse 

Osmosis water, but the water conductivity must be no 

less than 10 microSiemens/cm.

Potential for Airborne Contamination

Installing an ice machine near a source of yeast 

or similar material can result in the need for more 

frequent sanitation cleanings due to the tendency of 

these materials to contaminate the machine.

Most water filters remove chlorine from the water 

supply to the machine which contributes to this 

situation. Testing has shown that using a filter that 

does not remove chlorine, such as the Scotsman 

Aqua Patrol, will greatly improve this situation.

Warranty Information

The warranty statement for this product is provided 

separately from this manual. Refer to it for applicable 

coverage. In general warranty covers defects 

in material or workmanship. It does not cover 

maintenance, corrections to installations, or situations 

when the machine is operated in circumstances that 

exceed the limitations printed above.

Summary of Contents for F1222L



















Reviews: