background image

N0922L, N1322L, F1222L, F1522L

D Series Remote Low Side User Manual

October 2014

Page 12

Scale removal

Note: Following this procedure will reset the de-scale 

and sanitize light.

1.  Remove front panel.

2.  Push and release the Off button.

3.  Remove ice from bin or dispenser.

4.  Turn the water supply to the ice machine OFF.

5.  Drain the water and evaporator by disconnecting 

the leg of the hose connected to the water sensor 

and draining it into the bin. Return the hose to its 

original position.

6.  Remove the water reservoir cover.

7. 

Mix a solution of 8 ounces of Scotsman Clear One 

Scale Remover and 3 quarts of 95-115 degree F. 

potable water.

8.  Pour the scale remover solution into the reservoir. 

Use a small cup for pouring.

9. 

Push and release the Clean button: the auger 

drive motor and light are on, C is displayed and 

the De-scale light blinks. After 20 minutes the 

compressor will start.

10. Operate the machine and pour the scale remover 

into the reservoir until it is all gone. Keep the 

reservoir full. When all the scale remover solution 

has been used, turn the water supply back on. 

After 20 minutes of ice making the compressor 

and auger motor will shut off.

11. 

Turn the water supply to the ice machine OFF

12. Drain the water reservoir and evaporator by 

disconnecting the leg of the hose connected to 

the water sensor and draining it into the bin or a 

bucket. Return the hose to its original position. 

Discard or melt all ice made during the previous 

step.

13. 

To sanitize the water system, mix a locally 

approved sanitizing solution. An example of a 

sanitizing solution is mixing one ounce of liquid 

household bleach and two gallons of 95 – 115 

degree F. water.

14. Pour the sanitizing solution into the reservoir.

15. Push and release the On button.

16. Switch the water supply to the ice machine on.

17. Operate the machine for 20 minutes.

18. Push and release the Off button.

19. Wash the reservoir cover in the remaining 

sanitizing solution.

20. Return the reservoir cover to its normal position.

21. 

Melt or discard all ice made during the sanitizing 

process.

22. 

Wash the inside of the ice storage bin with the 

sanitizing solution.

23. Push and release the On button.

24. 

Return the front panel to its original position and 

secure with the original screws.

Scotsman Ice Machine 

Cleaner contains acids. These 

compounds may cause burns.

If swallowed, DO NOT 

induce vomiting. Give large 

amounts of water or milk. 

Call Physician immediately. 

In case of external contact, 

flush with water.

KEEP OUT OF THE

REACH OF CHILDREN

Summary of Contents for F1222L



















Reviews: