background image

TO INSTALL: Add On Kits

Door Kit: The door may be modified to accept a
decorator door panel.

Customizing Door Panel:

A custom door panel may be installed in front of
the standard one. Any panel 14

3

4

" wide, 28

15

16

"

high and

1

4

" thick or less at the edges may be used

as a decorator panel. Examples of decorator
panels include wood to match the adjacent
cabinets; metal of different colors to match nearby
appliances; or just about any material that will fit.
Scotsman has a stainless steel panel available to
fit this machine, the kit number is SS33.

If the material is less than 1/4" thick, the space
between the new panel and the original may be
filled with cardboard.

1. Remove single screw and the left
hand hinge filler plate from the top of the
door.

2. Remove two screws from the top of
the door and lift off the door handle.

3. Open the door slightly, about one-third
or so; then, remove the front screw
holding the hinge to the door.

4. Loosen the rear screw of the hinge
just enough to allow the door to sag or
move forward. This will allow access to
the top of the channels at the right and
left edges of the door.

5. From the top of the door, insert the
decorator panel (pre-cut) evenly into the
channels; carefully slide the panel all the
way down until the panel is fully into the
bottom channel.

6. Check that the panel is the in all the
way and does not protrude past the top
edge of the door.

7. Push the top hinge corner of the door
IN to align screw hole in the hinge with
the screw hole in the door. Install the
screw previously removed. Tighten the
other screw.

8. Replace the door handle and filler
plate; secure with screws previously
removed.

DCE33

September 2011

Page 11

Custom Panel,

Thin Panel

Shown With Filler

Hinge

Door With

Groove

Door Handle

Hinge

Filler Plate

Parts Involved in Customizing Door Panel

Summary of Contents for DCE33 Series













































Reviews: