Scotsman CME456R Page 36 Product Manual Download

Page: 36 / 36

CME456R

December 2000

Page 36

Before Calling for Service

Check the following:

1. Has the water supply to the ice machine or building been shut off? If yes, the

ice machine will automatically restart within 25 minutes after water begins to

flow to it.
2. Has power been shut off to the ice machine? If yes, the ice machine will

automatically restart when power is restored.
3. Did the remote condenser’s fan stop turning? If yes, the ice machine may

need to be manually reset.
4. Does the bin control have ice on it? If so, remove the ice and the machine

should start in a few minutes.

To Manually Reset the machine.

1. Remove the front panel.
2. Locate the AutoIQ Controller. If a red

diagnostic light is glowing, note which one

and its blink rate. Then push and release the

off button.
3. Push and release the Freeze button.
4. The machine should begin to operate. If

there is a lack of water it will soon shut off

again.
5. Return the front panel to its normal

position.
If the machine shuts down again, call for

service.

To Shut the Machine Off:

1. Remove the front panel.
2. Locate the AutoIQ Controller.
3. Push and hold the Off button for 3

seconds or until the machine stops.

BIN FULL

FREEZE

HARVEST

CLEAN

OFF

WATER
REFRIGERATION

PUSH BUTTON

CONTROL SWITCHES

INDICATOR LIGHTS:

DIAGNOSTIC LIGHTS:

Summary of Contents for CME456R





































Search results

Summary of Contents for CME456R

Reviews:

Related manuals for CME456R

Brands by name

Popular brands

Scotsman CME456R, Product Manual

Search results

Summary of Contents for CME456R

Reviews:

Related manuals for CME456R

Brands by name

Popular brands