Scotsman BC0530 Service Manual Download

Page: 20 / 42

BC0530 Service Manual

March 2020

Page 20

>4 After 3 consecutive occurrences of fault 4 the

machine will attempt to remove any blockages by

defrosting and cycling water – LED40 will be flashing

(5Hz) during this defrost and water cycle-defrost will

last for 5 minutes –Water will cycle for 10 minutes –if

the machine has 3 more consecutive short freeze

cycles, LED 40 will be solid and the machine will shut

down.

Water fill exceeds 3 minutes then the Valve

closes & waits 10 minutes, as LED 60 Flashes. Valve

then opens & tries again. This routine repeats 3X and

results in a solid Code 6, if the fill is not completed on

the third try.
>7 Both Arm-Up/Arm Down (Cam ) Switches

Closed (un-actuated ) at the same time (not allowed ).
>8

Indicates that the machine is in full rinse mode

(left jumper pulled)
>9

Indicates bin full, Ice machine will be shut

down after current batch is complete.
Note: The controller will need to be reset to clear

these error codes. Board Revision numbers are

found on the sticker placed on a processor chip in the

middle of the control board. Example: 2.0

Stacked Jumpers:

• Under normal operation all machines will have a

jumper on the pins marked full rinse. If this jumper

is removed the water valve will stay energized to

thoroughly rinse the water plate during the water

plate lowering, harvest and water plate rising

cycles.

Note: The machine will need reset for the controller to

acknowledge this change.
• The right jumper is used to tell the controller when

it is being used on a dual evaporator machine.

BCO530 should not have jumper on.

Note: if you are replacing control board the new board

will come with jumper on. (MUST BE REMOVED OR

PLATE WILL NOT RISE).

Programming Port:

Used by service technicians to

alter or update the controller software.

Water Level Sensor:

Port for water level FLOATS.

Evaporator Temperature Adjustment:

To increase

the temperature of the evaporator at which the water

plate closes, turn this dial counterclockwise. To

decrease, turn the dial clockwise. The operator can

adjust the harvest termination temperature between

35 and 60F.

Note: After adjustment the controller must be reset.

Reset Button:

Reboots the controller.

Temperature Sensor Port:

For evaporator and bin

temperature sensor probes.

Bin Full Adjustment:

To increase the temperature at

which the ice level probe reacts to contact with ice in

the bin turn the dial clockwise. To decrease, turn the

dial counterclockwise. The temperature range for this

adjustment is between 33 and 45F.
Note: After adjustment the controller must be reset.

Switch Input Port:

For the on/off, ice/clean and limit

switches

Factory Use Only:

Used to display diagnostic codes

to an LCD monitor used only by service the factory.

Output:

AC output for powering the fan(s),

compressor, water pump(s), actuator motor(s),

contactor(s), and valves.

Summary of Contents for BC0530











































Search results

Summary of Contents for BC0530

Reviews:

Related manuals for BC0530

Brands by name

Popular brands

Scotsman BC0530, Service Manual

Search results

Summary of Contents for BC0530

Reviews:

Related manuals for BC0530

Brands by name

Popular brands