background image

BC0530 Service Manual

March 2020

Page 38

TROUBLE SHOOTING

Problem

Possible Cause

Solution

Defrost valve opens 

during water fill.

Slow water fill.

The water supply pressure must be a 

minimum of 5 PSI (34 KPA) dynamic at 

the water valve.  Be sure that the supply 

line is of adequate size.  This is especially 

important for liquid cooled models where 

the potable water and condenser coolant 

water are supplied by the same water 

line.  Check for restrictions in the wa

-

ter supply line including clogged filters.  

Check the water line strainer and clean it 

if needed.   

Cold potable water supply.

This is normal operation of the unit, if the 

water supply is too cold.  Very cold water 

will not rinse the ice residue from the wa-

ter plate, causing it to build up and affect 

normal operation.

Ice remains attached to 

the water plate surface 

at the end of defrost.

Ice frozen into the water plate surface.  

Thick web between ice cubes.

Adjust web thickness to specifications.  

Ice frozen into the water plate surface.  

Cubes are fully formed without small dim-

ples.

Reduce the water level until ice cubes are 

produced with small dimples.

Over-freezing

Be sure that the control stream does 

not go over the dam for longer than 15 

seconds.

Cold potable water supply.

Very cold water will not rinse the ice resi-

due from the water plate thoroughly.

Summary of Contents for BC0530











































Reviews: