1982-89 Buick Skyhawk
1982-88 Oldsmobile Firenza
Read pages 3-6
for kit assembly.
RADIO REMOVAL:
1. Disconnect the support strap from the glove box door.
2. Remove the four screws securing the glove box liner.
3. Pull the glove box liner outward and remove it.
4. Remove the two screws from below
the lighter/heater controls.
5. Remove the three screws
securing the lower dash panel
TOP
TOPE
"C1" BRACKET USE HOLE #5
"C1" SOPORTE USA ABERTURA
NO. 5
"B1" BRACKET
USE HOLE #2
"B1" SOPORTE
USA ABERTURA
NO. 5
(each side of the
"C2" BRACKET
steering
column).
6. Pull the panel down
USE HOLE #5
"C2" SOPORTE
USA ABERTURA
to expose the screw
NO. 5
BOTTOM
under the panel, and
FONDO
to the left of the heater control.
"B2" BRACKET USE HOLE #5
"B2" SOPORTE USA ABERTURA NO. 5
Unsnap the panel assembly and remove it.
7. Remove the four screws securing the radio
to the dash; pull the radio out of the dash cavity.
8. Disconnect the antenna and all the electrical connections, then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
CARRIAGE BOLT
1992-95 Buick Skylark
Read pages 3-6
PERNO DE PORTE
RADIO REMOVAL:
for kit assembly.
1. Pull out on the ashtray and extract the two screws
securing the rear of the ashtray assembly.
2. Extract the two screws securing the front of the
ashtray and the lower section of the radio trim
bezel in the ashtray cavity.
BOTTOM
FONDO
3. Carefully pry outward on the radio trim bezel
with a panel removal tool/screwdriver to
release the fastening clips securing it to the
dash and remove.
FLANGE NUT
TUERCO REBORDE
4. Remove the two nuts from the bottom of the
radio chassis securing the radio to the dash.
Pull the radio from the cavity, unplug all the
connectors, and remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1983-85 Buick Skylark
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Remove the four 9/32 inch hex head screws from the top of the
instrument cluster trim panel. Remove one hex head sheet metal
screw from the bottom left of the instrument cluster trim panel.
2. Remove the two 7mm hex head sheet metal screws from
the trim below the steering column and remove the trim.
"C1" BRACKET USE HOLE #5
"C1" SOPORTE USA ABERTURA
NO. 5
3. Place the ignition in the "on" position, apply the
emergency brake and put the transmission in second gear.
Carefully remove the trim panel from the dash and
"B1" BRACKET
around the steering column.
USE HOLE #2
TOP
"B1" SOPORTE
TOPE
4. Remove the four
USA ABERTURA
7mm hex head
NO. 5
sheet metal screws
"C2" BRACKET
from the radio
USE HOLE #5
"C2" SOPORTE
mounting
brackets.
USA ABERTURA
Slide the radio out
NO. 5
of the cavity. Disconnect
BOTTOM
FONDO
all the wiring and remove the radio.
"B2" BRACKET USE HOLE #5
"B2" SOPORTE USA ABERTURA NO. 5
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
9