1986-88 Chevrolet Monte Carlo
Read pages 3-6
for kit assembly.
1986-87 Chevrolet El Camino
RADIO REMOVAL:
"A1" BRACKET
"B1" BRACKET USE HOLE #1
LEFT SIDE
USE HOLE #4
1. Remove the two
"B1" SOPORTE USA
LADO IZQUIERDA
"A1" SOPORTE USA
RIGHT SIDE
ABERTURA
screws from the top
ABERTURA
LADO DERECHO
NO.1
NO. 4
of the radio trim panel
and the two screws
from the bottom
edge of the trim panel.
2. Remove the four screws
which secure the radio,
slide the radio out of the
FRONT OF KIT
dash cavity and
FRENTE DE
disconnect
ESTUCHE
"C2" BRACKET
"D2"
USE HOLE #4
the wiring connectors.
BRACKET USE HOLE #1
3. Remove the radio.
"C2" SOPORTE USA ABERTURA NO. 4
"D2" SOPORTE USA ABERTURA NO. 1
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1985-88 Chevrolet Nova
Read pages 3-6
RADIO REMOVAL:
for kit assembly.
1. Remove the ashtray and extract the two screws from the
"B1" BRACKET
ashtray bracket. Then remove the bracket.
USE HOLE #2
LEFT SIDE
2. Extract the two screws
"A1" BRACKET USE HOLE #4
LADO IZQUIERDA
RIGHT SIDE
"B1" SOPORTE USA
"A1" SOPORTE USA
LADO DERECHO
ABERTURA
from the top edge of the
ABERTURA NO. 4
NO.2
radio trim panel, pull the
trim out and remove the panel.
3. Remove the four screws which
secure the radio to the dash,
slide the radio out of the
dash cavity, disconnect the
wiring harnesses and
remove the radio.
FRONT OF KIT
FRENTE DE
4. Remove the two hex
"C2" BRACKET
nuts from the factory
USE HOLE #4
"B2" BRACKET
ESTUCHE
"C2" SOPORTE USA ABERTURA NO. 4
USE HOLE #3
radio mounting bracket,
"B2" SOPORTE USA
one from each side of the radio, and remove the bracket from the radio.
ABERTURA NO. 3
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1998-01 Chevrolet S-10 Blazer
Read pages 3-6
1998-01 Chevrolet S-10 Pickup
for kit assembly.
1998-01 GMC S-15 Jimmy
1998-01 GMC Sonoma Pickup
1998-00 Isuzu Hombre Pickup
RADIO REMOVAL:
"A1" BRACKET USE HOLE #2
"B1" BRACKET USE HOLE #2
"A1" SOPORTE USA
"B1" SOPORTE USA ABERTURA NO.2
1. Extract the (2) screws
ABERTURA NO. 2
securing the top area
of the driver's side
underdash cover panel.
2. Pull the driver's side
underdash down to
access and extract
LEFT SIDE
(2) 7mm hex screws
LADO
IZQUIERDA
RIGHT SIDE
holding the bottom
FRONT OF KIT
LADO
DERECHO
of the dash bezel.
FRENTE DE
3. Extract the screw located in the top edge
ESTUCHE
of the dash panel at the instrument cluster.
4. Carefully pry out on the dash bezel to release the fastening clips securing the bezel to the dash and
unplug headlight / misc. switches on the driver's (left) of the bezel.
CAUTION:
At this point, take care around the hazard switch, by tilting the wheel down and/or depressing the
switch so the panel will clear. Also take care to snap the passenger air bag switch from the dash panel and
push it back trhough its own hole rather than unplugging the switch. It is a costly repair bill in excess of $400
to replace the hazard switch.
5. Remove the dash bezel from the vehicle.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
19