background image

Ignition Disable / Anti-hijack Module (RID-5) 

 
Installation 
 
1.

 

Cut the Ignition / Engine control wire (refer to options below) 

2.

 

Attempt to start bike to test if correct wire is selected.  If bike starts the wrong wire is selected. 
(contact Aritronix for assistance)  If bike does not start, correct wire was selected continue to 
step 3. 

3.

 

When Packaged the RID-5 wire ends have been treated with clear silicon to protect the 
ends from fraying. Make sure they are stripped bare of this before continuing. 

4.

 

Connect one end of cut wire to one of the blue tap wires in RID-5 with provided butt 
connector or any other solid connection options. 

5.

 

Connect second end of cut wire to second blue tab wire in RID-5 with provided butt 
connector or any other solid connection options. 

6.

 

Test connections to insure that they are as solid as possible. * 

7.

 

Plug the RID-5 connector into the matching connector on Main Control Module (MCM) 
Accessory Harness. 

8.

 

Test RID-5 by activating alarm (without perimeter sensor) and try to turn on bike.  If bike turns 
on, please contact Aritronix for assistance. 

 
* Failure to test for a loose wire could cause an accidental engine cut off. 
 
The Ignition / Engine control wire Options: 
 
Option #1:   Positive lead wire on fuel pump 
Option #2:   Positive lead wire on fuel injection system 
Option #3:   Positive wire that goes to the ignition fuse in fuse box.  This should be  

      either a 10 or 15 amp fuse labeled IGN or START. (Carbureted Bikes) 

Option #4:   Ground wire from ignition module 
Option #5:   Positive wire from ignition module to ignition coil 
Option #6:   Wire connected between the ignition module and engine stop button 
 
Operating the Anti-Hijack feature 
 
While the engine is running, press and hold the transceivers’ button #1 and button #2 at the same 
time for 5 seconds. The siren will begin to chirp confirming that the Anti-Hijack feature has been 
activated. 15 seconds later, the siren will go off continuously, and the engine will shut down. To 
disarm, turn off the ignition switch and press button #2. 

 
 
 
 

 
 
 
 

To Accessory Harness on 
Main Control Module (MCM) 

 
 
 
 
 
 

To CUT wire on Motorcycle 

 
 

 

13 

 
 

Summary of Contents for SR-i500

















Reviews: