scope ConneXions II V7 SDC Installation & User Manual Download Page 11

Page: 11 / 13

ConneXions II V7 SDC DC, Single Port Version

CONV7SDC 07/05

Issue 4

System Specification

System Operating Voltage:

13.8V dc

System Power Consumption:

less than 50mA standby, 300mA (transmit)

Transmitter:

Power output:

500mW max

Frequency Range:

450-470 MHz

Channel Spacing:

25 KHz

Adjacent Channel:

better than 200nW @ 4.5 KHz deviation

TX Baud Rate:

512 or 1200

Type Approval:

ETS 300 224, MPT1383 Cert. No. 13249

Type Approval No:

13249 CONX7DC

EMC Approval:

EC Type Approved to ETS 300 682, Approval No: 13331

General:

Ports:

RS232

serial

PL2

Optional 10 way dry contact I/F on PL1

Comms Baud Rate:

600 to 9600 software adjustable*

Footprint (mm):

328 (L) x 190 (W) x 75 (D) max

*dependent on system configuration

excluding aerial

Scope’s policy is one of continuous development and specifications are subject to change without notice

Summary of Contents for ConneXions II V7 SDC














Search results

Summary of Contents for ConneXions II V7 SDC

Reviews:

Related manuals for ConneXions II V7 SDC

Brands by name

Popular brands

scope ConneXions II V7 SDC, Installation & User Manual

Search results

Summary of Contents for ConneXions II V7 SDC

Reviews:

Related manuals for ConneXions II V7 SDC

Brands by name

Popular brands