background image

8

  Warranty

7

  Maintenance and Parts

CARE

•  To clean the trailer: use only mild soap and water. Do not use 

cleaning solvents.

•  Do not leave trailer outside after use. Inclement weather and 

harsh elements may stress the fabric on the trailer

•  Routinely check that all fasteners and equipment (wheels, 

reflectors, flag, etc) are tight and properly assembled.

•  Check the tire pressure often. The recommended tire pressure 

range is printed on the tire. Only use a foot or hand pump to 

inflate.

•  Have a qualified bicycle mechanic perform routine safety 

checks on your bicycle before using with the trailer.  

•  Routine bicycle maintenance is recommended to be 

performed every year.

ACCESSORIES

•  1pc Trailer Coupler
•  1pc Tab Washer
•  1pc Locking Pin
Please direct any accessory (small parts) and warranty inquiries to 

Pacific Cycle Customer Service at 1-800-242-6110.

Pacific Cycle warrants this product to be free of defective materials 

and workmanship for 1 year from the date of original purchase.
THIS LIMITED WARRANTY IS THE ONLY WARRANTY APPLICABLE  

TO THIS PRODUCT, AND IS EXPRESSLY IN LIEU OF ANY OTHER 

WARRANTY.  This limited warranty gives you specific legal rights 

and you may also have other rights which may vary from state  

to state.
This warranty is extended only to the original consumer purchaser 

for non-commercial use and does not cover tires or tubes, or other 

wear parts, ordinary wear and tear, abuse, misuse, neglect, theft, 

or damage due to accident.
PACIFIC CYCLE IS NOT RESPONSIBLE FOR INCIDENTAL OR 

CONSEQUENTIAL DAMAGES. THIS LIMITED WARRANTY DOES NOT 

COVER ANY PERSONAL INJURIES, DAMAGE TO, OR, FAILURE OF THE 

PRODUCT OR ANY OTHER LOSSES DUE TO ACCIDENT, ABUSE, 

MISUSE, ALTERATION, NEGLECT, NORMAL WEAR AND TEAR, 

IMPROPER ASSEMBLY, IMPROPER FIT, IMPROPER MAINTENANCE 

OR USE OF UNAUTHORIZED REPLACEMENT PARTS NOT DESIGNED 

FOR THE PRODUCT.
To make a claim under warranty, notification of such defect must 

be given to Pacific Cycle, Inc. at 1-800-242-6110. You will be 

instructed on how the product or part needing replacement should 

be shipped, postpaid, to Pacific Cycle, Inc.  

Schwinn Cargo Trailer • model 13-SC320       22

Summary of Contents for 13-SC320



























Reviews: